Home › Engine / Hybrid System › G16E-GTS (FUEL) › FUEL INJECTOR (for Direct Injection) › from 2020.09
RM36W0E _51 Engine / Hybrid System _095688 G16E-GTS FUEL _0449367 FUEL INJECTOR(for Direct Injection) A

G16E-GTS FUEL  FUEL INJECTOR(for Direct Injection)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 23255A 1.INSTALL FUEL INJECTOR SEAL

a.
A401665C01
0.625,0.427 0.938,0.583 0.313,0.156 10 false *a
*a Area to be Cleaned


Apply engine conditioner to the area shown in the illustration. Using a piece of cloth, clean carbon deposits from the fuel injector assembly and its grooves.

NOTICE:
·

Do not clean the tip of the fuel injector assembly.

·

Do not use a wire brush to clean the fuel injector assembly.

·

If a fuel injector assembly is dropped or the tip of the fuel injector assembly is struck, replace it with a new one.




b.
A401666C01
0.219,0.979 0.344,0.979 0.344,0.979 0.458,1.125 false 2.104,0.813 2.563,0.813 2.563,0.813 2.563,1.677 false 2.24,0.813 2.24,1.688 false 0.073,0.885 0.385,1.042 0.313,0.156 10 false *a 1.948,0.729 2.26,0.885 0.313,0.156 10 false *b
*a SST (Guide)
*b Chamfer


Apply engine oil to the fuel injector assembly contact surface of SST (guide), then attach SST (guide) to the fuel injector assembly with the chamfer facing the tip of the fuel injector assembly as shown in the illustration.

SST
09260-39030  (09261-03030)


c.
A273085C03
0.99,2.635 1.49,2.635 false 1.01,2.802 1.396,3.042 1.396,3.042 1.49,3.042 false 1.531,2.563 1.729,2.76 0.198,0.198 10 false *a 2.771,0.563 2.969,0.76 0.198,0.198 10 false *c 1.979,0.552 2.177,0.75 0.198,0.198 10 false *b 1.542,2.969 1.74,3.167 0.198,0.198 10 false *1
*1 Fuel Injector Seal
*a SST (Holder)
*b Correct
*c Incorrect


Install a new fuel injector seal to SST (holder).

SST
09260-39030  (09261-03011)

NOTICE:

Be careful not to install the fuel injector seal to SST (holder) at an angle. Doing so will stretch the fuel injector seal.



d.
A401667C01
0.802,1.083 0.917,0.406 0.917,0.406 1.063,0.406 true 1.01,1.719 1.125,1.948 1.125,1.948 1.281,1.948 true 1.104,0.323 1.417,0.479 0.313,0.156 10 false *a 1.333,1.885 1.646,2.042 0.313,0.156 10 false *b
*a SST (Holder)
*b SST (Guide)


Install SST (holder) with the fuel injector seal to the tip of the fuel injector assembly. Slide the fuel injector seal downward into the fuel injector assembly groove with your fingers as shown in the illustration.

SST
09260-39030  (09261-03011, 09261-03030)

HINT:

Check that the fuel injector seal is seated in the fuel injector assembly groove as shown in the illustration.



e.
A401668C01
0.667,1.333 0.917,0.417 0.917,0.417 1.104,0.417 true 1.146,0.344 1.458,0.5 0.313,0.156 10 false *a
*a SST (Guide)


Slowly slide SST (guide) toward the tip of the fuel injector assembly. When the fuel injector assembly contact surface of SST (guide) aligns with the fuel injector seal as shown in the illustration, hold the position for 5 seconds or more to fully seat the fuel injector seal into the fuel injector assembly groove.

SST
09260-39030  (09261-03030)

NOTICE:

Make sure the fuel injector seal is not pinched between SST (guide) and the edge of the fuel injector assembly groove. Replace the fuel injector seal if it becomes damaged.


HINT:
·

Set SST (guide) so that its bottom surface is flush with the fuel injector seal.

·

If it is difficult to slide SST (guide) upward, slowly wiggle it from side to side while sliding it up the fuel injector assembly little by little.




f.
A401669C01
0.625,2.771 0.938,2.927 0.313,0.156 10 false *a 1.844,2.75 2.156,2.906 0.313,0.156 10 false *b 2.75,2.729 3.063,2.885 0.313,0.156 10 false *c 0.583,0.667 0.896,0.823 0.313,0.156 10 false *d 1.792,0.656 2.104,0.813 0.313,0.156 10 false *e 2.708,0.656 3.021,0.813 0.313,0.156 10 false *e
*a Normal
*b Protruding
*c Deformed
*d Correct
*e Incorrect


After installing the fuel injector seals, check that they are not scratched, deformed or protruding from the fuel injector assembly groove.

NOTICE:

If a fuel injector seal is scratched, deformed or protruding from the groove, replace it with a new one.


HINT:

Use the same procedure to install the other fuel injector seals.



Hide 23250E 2.INSTALL DIRECT FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A401670C01
0.979,0.583 1.094,0.583 1.094,0.583 1.25,0.948 false 2.292,0.375 2.417,0.375 2.417,0.375 2.604,0.656 false 2.438,0.167 2.542,0.167 2.542,0.167 2.771,0.448 false 2.917,0.115 3.031,0.115 3.031,0.115 3.031,0.51 true 0.813,0.51 1.125,0.667 0.313,0.156 10 false *1 2.115,0.302 2.427,0.458 0.313,0.156 10 false *2 2.26,0.094 2.573,0.25 0.313,0.156 10 false *3 2.75,0.021 3.063,0.177 0.313,0.156 10 false *a
*1 Fuel Injector Assembly
*2 C-ring
*3 Injector Vibration Insulator
*a Taper


Install a new injector vibration insulator and C-ring to each fuel injector assembly.

NOTICE:
·

Install the taper of the injector vibration insulator by aligning it with the taper of the fuel injector assembly.

·

Check that the C-ring is securely seated in the groove of the fuel injector assembly.




b.

Install a new O-ring and No. 1 fuel injector back-up ring to each fuel injector assembly as shown in the illustration.

A401671C01
5.198,1.313 5.333,1.313 5.333,1.313 5.625,1.792 true 5.917,1.719 6.115,1.281 6.115,1.281 6.219,1.281 true 5.031,1.229 5.344,1.385 0.313,0.156 10 false *1 6.271,1.198 6.583,1.354 0.313,0.156 10 false *2 1.573,0.656 1.885,0.813 0.313,0.156 10 false *a 0.771,1.792 1.083,1.948 0.313,0.156 10 false *b 2.542,1.813 2.854,1.969 0.313,0.156 10 false *c 1.625,1.125 1.938,1.281 0.313,0.156 10 false *d 0.76,1.125 1.073,1.281 0.313,0.156 10 false *e 2.531,1.135 2.844,1.292 0.313,0.156 10 false *e
*1 No. 1 Fuel Injector Back-up Ring *2 O-ring
*a No. 1 Fuel Injector Back-up Ring Opening *b Overlapped
*c Stretched *d Correct
*e Incorrect - -


NOTICE:
·

Check that there is no foreign matter or damage on the O-ring groove of the fuel injector assembly.

·

Make sure that the No. 1 fuel injector back-up ring is installed in the correct orientation.

·

Make sure that the No. 1 fuel injector back-up ring and O-ring are installed in the correct order.

·

Check that the opening of the No. 1 fuel injector back-up ring is not overlapped or stretched as shown in the illustration.

·

After installing the O-ring, check that it is not contaminated with foreign matter and is not damaged.




c.
A401672C01
2.833,1.5 3.031,1.5 false 2.76,2.375 2.896,2.281 2.896,2.281 3,2.281 false 2.448,2.448 2.656,2.833 2.656,2.833 2.792,2.833 true 3.073,1.417 3.385,1.573 0.313,0.156 10 false *1 3.042,2.198 3.354,2.354 0.313,0.156 10 false *2 2.833,2.75 3.146,2.906 0.313,0.156 10 false *a
*1 Fuel Injector Assembly
*2 No. 3 Fuel Injector Back-up Ring
*a Notch


With the notch of a new No. 3 fuel injector back-up ring facing downward, install the No. 3 fuel injector back-up ring to each fuel injector assembly as shown in the illustration.

NOTICE:
·

Make sure that the No. 3 fuel injector back-up ring is installed in the correct orientation.

·

After installing the No. 3 fuel injector back-up ring, make sure there is no damage or foreign matter.




d.

Install the nozzle holder clamp to each fuel injector assembly.


e.
A472090C01
0.656,0.594 1.396,0.854 true 0.802,1.188 1.385,1 true 0.469,0.5 0.781,0.656 0.313,0.156 10 false *a 0.635,1.115 0.948,1.271 0.313,0.156 10 false *b
*a Protrusion
*b Positioning Hole
V100135

No Gap


Align the protrusion of the nozzle holder clamp with the positioning hole of the fuel delivery pipe and insert the fuel injector assembly.

NOTICE:
·

Make sure that there is no foreign matter or damage inside the fuel injector assembly installation holes (fuel delivery pipe).

·

Do not allow gasoline to get on the O-rings or inside the installation holes.

·

If it is difficult to insert the fuel injector assembly, apply new engine oil to the chamfer of the fuel injector assembly installation hole of the fuel delivery pipe. Be careful not to allow the fuel injector assembly to fall out of the fuel delivery pipe.

·

Do not tilt the fuel injector assembly when inserting it into the fuel delivery pipe.

·

Check that there is no gap between the fuel delivery pipe and the nozzle holder clamp.

·
A401674C01
1.073,1.656 1.51,1.656 true 1.74,1.646 2.271,1.24 2.271,1.24 2.469,1.24 true 2.521,1.167 2.833,1.323 0.313,0.156 10 false *a 0.906,1.583 1.219,1.74 0.313,0.156 10 false *b
*a QR Code
*b Flow Classification Number


Make sure the 3 fuel injector assemblies have the same flow classification number and that the flow classification number is 1, 2, 3, 4, 5, 6, 7, 8 or 9.




Hide 82126A 3.INSTALL NO. 6 ENGINE WIRE

a.

Connect the 3 fuel injector assembly connectors and install the No. 6 engine wire to the fuel delivery pipe.


b.

Engage the 2 clamps.


Hide 23814B 4.INSTALL FUEL DELIVERY PIPE

NOTICE:

When replacing the fuel delivery pipe, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.


a.

Apply lubricant to the fuel injector assembly installation holes of the cylinder head sub-assembly.


b.

Temporarily install the fuel delivery pipe to the cylinder head sub-assembly.

NOTICE:
·

If a fuel injector assembly is dropped or the tip of a fuel injector assembly is struck, replace it with a new one.

·

Check that there is no foreign matter or damage on the fuel injector assembly installation holes of the cylinder head sub-assembly.

·

When installing the fuel delivery pipe, push it in evenly without tilting it.




c.

Temporarily install the 4 bolts.


d.
A476538N01
2.396,0.656 2.563,0.833 0.167,0.177 10 true 1 2.875,0.667 3.042,0.844 0.167,0.177 10 true 4 0.073,0.656 0.24,0.833 0.167,0.177 10 true 3 1,0.667 1.167,0.844 0.167,0.177 10 true 2

Install the fuel delivery pipe by uniformly tightening the 4 bolts in the order shown in the illustration.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 16278 5.INSTALL NO. 2 WATER BY-PASS PIPE

a.

Install the No. 2 water by-pass pipe with the 2 bolts.

Torque:
10 N・m (102 kgf・cm, )


Hide 23801P 6.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 9. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 11.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION