Home › Engine / Hybrid System › G16E-GTS (FUEL) › FUEL PUMP (for High Pressure) › from 2020.09
RM36W0E _51 Engine / Hybrid System _095688 G16E-GTS FUEL _0449364 FUEL PUMP(for High Pressure) A

G16E-GTS FUEL  FUEL PUMP(for High Pressure)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 23100X 1.TEMPORARILY INSTALL FUEL PUMP ASSEMBLY

NOTICE:

When replacing the fuel pump assembly, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.


HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A476553C01
1.938,1.125 2.417,0.75 true 1.281,2.521 1.448,2.521 false 1.229,3.094 1.396,3.094 false 1.333,4.042 1.5,4.042 false 2.875,2.521 3.042,2.521 false 2.802,2.969 2.969,2.969 false 2.958,4.021 3.125,4.021 false 1.458,2.406 1.667,2.573 0.208,0.167 10 false *1 1.385,3 1.573,3.177 0.188,0.177 10 false *2 2.438,0.656 2.635,0.823 0.198,0.167 10 true *3 0.865,2.313 1.177,2.469 0.313,0.156 10 false *a 2.448,2.292 2.76,2.448 0.313,0.156 10 false *b 3.052,2.417 3.26,2.583 0.208,0.167 10 false *1 2.99,2.865 3.177,3.042 0.188,0.177 10 false *2 1.51,3.927 1.708,4.094 0.198,0.167 10 true *3 3.156,3.917 3.354,4.083 0.198,0.167 10 true *3
*1 Fuel Pump Assembly
*2 Fuel Pump Lifter Assembly
*3 No. 2 Camshaft
*a Correct
*b Incorrect


Turn the crankshaft pulley until the flat of the No. 2 camshaft faces the fuel pump lifter assembly.

HINT:

This prevents the No. 2 camshaft nose from pushing up the fuel pump lifter assembly when installing the fuel pump assembly.



b.
A476554C01
1.26,1.427 1.26,2.094 true 1.896,1.115 2.333,0.708 true 0.948,4.281 1.344,4 true 1.188,2.125 1.5,2.281 0.313,0.156 10 false *1 2.375,0.583 2.542,0.74 0.167,0.156 10 true *a 0.76,4.198 1.073,4.354 0.313,0.156 10 false *b
*1 Fuel Pump Spacer Gasket
*a Pump Drive Cam (Engine Oil Application Area)
*b Fuel Pump Lifter Assembly (Engine Oil Application Area)


Apply 30 cc (1.8 cu. in.) of engine oil to the pump drive cam.


c.

Apply engine oil to the fuel pump lifter assembly.


d.

Install a new fuel pump spacer gasket to the cylinder head cover sub-assembly.


e.
A476555C01
1.896,2.521 2.375,2.25 true 1.917,1.75 2.146,1.75 true 1.208,2.167 1.5,2.375 true 1.229,1.635 1.458,1.635 true 1.021,1.531 1.208,1.719 0.188,0.188 10 true *a 1.01,2.052 1.188,2.229 0.177,0.177 10 true *b 2.177,1.646 2.365,1.823 0.188,0.177 10 true *c 2.406,2.167 2.594,2.354 0.188,0.188 10 true *d
*a Fuel Pump Lifter Assembly (Engine Oil Application Area)
*b Fuel Pump Lifter Guide (Engine Oil Application Area)
*c Stopper Key
*d Key Groove


Apply engine oil to the inside of the fuel pump lifter guide and the outside of the fuel pump lifter assembly.


f.

Set the fuel pump lifter assembly on the fuel pump lifter guide as shown in the illustration.

HINT:

Align the stopper key of the fuel pump lifter assembly with the key groove of the fuel pump lifter guide.



g.
A464884

Apply engine oil to a new O-ring and install it to the fuel pump assembly.

NOTICE:

Do not damage the O-ring.



h.
A472042

Set the fuel pump flange and fuel pump assembly on the cylinder head cover sub-assembly as shown in the illustration.


i.

Temporarily install the fuel pump assembly with the 2 bolts, leaving some allowance for left and right movement.


Hide 17893 2.INSTALL INTAKE AIR RESONATOR

a.

Install the intake air resonator to the fuel pump flange with the bolt.


Hide 25761B 3.INSTALL NO. 1 VACUUM TRANSMITTING HOSE

a.

Engage the 2 clamps and connect the No. 1 vacuum transmitting hose.


Hide 82121 4.CONNECT ENGINE WIRE

a.

Engage the clamp and connect the engine wire.


b.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the 2 connectors.


Hide 23801P 5.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

NOTICE:

Do not damage the seals of the union nuts of the No. 1 fuel pipe sub-assembly.


a.
A472038

Temporarily install the bolt.


b.

Temporarily install the No. 1 fuel pipe sub-assembly to the fuel delivery pipe and tighten the union nut by hand.


c.

Temporarily install the No. 1 fuel pipe sub-assembly to the fuel pump assembly and tighten the union nut by hand.


Hide 23100X 6.INSTALL FUEL PUMP ASSEMBLY

a.

Tighten the 2 bolts.

A476556

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


b.

Connect the fuel pump assembly connector.


Hide 23801P 7.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

a.

Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

A476557C01
6.229,0.958 6.385,0.771 false 6.417,0.667 6.635,0.844 0.219,0.177 10 false *a 5.292,0.656 5.604,0.813 0.313,0.156 10 false *b
*a 17 mm Union Nut Wrench *b Torque Wrench Fulcrum Length


Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




b.

Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:
Specified tightening torque : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not adjust the torque in the loosening direction.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




c.

Tighten the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16261G 8.CONNECT NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose and slide the clip to secure it.


Hide 16296 9.CONNECT NO. 8 WATER BY-PASS HOSE

a.

Connect the No. 8 water by-pass hose and slide the clip to secure it.


Hide 23902 10.INSTALL NO. 2 FUEL TUBE SUB-ASSEMBLY

a.

Connect the No. 2 fuel tube sub-assembly to the fuel pump assembly and fuel delivery pipe.


b.

Install the No. 2 fuel tube sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23841G 11.INSTALL FUEL HOSE CLAMP

a.

Install the fuel pipe clamp to the No. 2 fuel tube sub-assembly.


Hide 23901 12.CONNECT NO. 1 FUEL TUBE SUB-ASSEMBLY

a.

Connect the No. 1 fuel tube sub-assembly to the No. 2 fuel tube sub-assembly.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 25860 13.INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

Hide 12601B 14.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 55701J 15.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 16.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55734A 17.INSTALL WATER GUARD PLATE RH (for LHD)

Hide 55735A 18.INSTALL WATER GUARD PLATE LH (for RHD)

Hide 55815E 19.INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 20.INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 21.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 22.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 23. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 25.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION