Home › Engine / Hybrid System › G16E-GTS (FUEL) › FUEL INJECTOR (for Port Injection) › from 2020.09
RM36W0E _51 Engine / Hybrid System _095688 G16E-GTS FUEL _0449369 FUEL INJECTOR(for Port Injection) A

G16E-GTS FUEL  FUEL INJECTOR(for Port Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of fuel injector assembly Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 12601B 3.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 23841K 5.REMOVE FUEL PIPE CLAMP

a.
A472035

Remove the fuel pipe clamp from the fuel tube connector.


Hide 23902 6.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A472075

Disconnect the No. 2 fuel tube sub-assembly from the fuel delivery pipe sub-assembly.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 16288 7.DISCONNECT NO. 4 WATER BY-PASS PIPE

a.
A472076

Remove the 3 bolts and No. 4 water by-pass pipe from the cylinder head sub-assembly.


Hide 15301B 8.REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY

a.
A472077

Remove the oil level gauge sub-assembly.


Hide 11452D 9.REMOVE OIL LEVEL GAUGE GUIDE

a.
A472078

Remove the bolt and oil level gauge guide from the cylinder head sub-assembly.


b.

Remove the O-ring from oil level gauge guide.


Hide 23825 10.REMOVE FUEL DELIVERY GUARD

a.
A472079

Disengage the wire harness clamp.


b.

Remove the 2 bolts, 2 nuts and fuel delivery guard.


Hide 23814B 11.REMOVE FUEL DELIVERY PIPE

a.
A472080

Disconnect the connector.


b.

Remove the 2 bolts and fuel delivery pipe with the 3 fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.



Hide 23891 12.REMOVE FUEL DELIVERY SPACER

a.
A472081

Remove the 2 fuel delivery spacers from the cylinder head sub-assembly.


Hide 23291A 13.REMOVE INJECTOR VIBRATION INSULATOR

a.
A472082

Remove the 3 injector vibration insulators from the cylinder head sub-assembly.


Hide 82125N 14.REMOVE NO. 5 ENGINE WIRE

a.
A472083

Disconnect the 4 connectors from the 3 fuel injector assemblies and fuel pressure sensor.


b.

Disengage the 2 clamps to remove the No. 5 engine wire from the fuel delivery pipe.


Hide 23250F 15.REMOVE PORT FUEL INJECTOR ASSEMBLY

a.
A472084

Pull the 3 fuel injector assemblies out of the fuel delivery pipe.


b.
A401653

Remove the O-ring from each fuel injector assembly.


c.
A401654N01
2,0.417 2.771,0.615 0.771,0.198 10 false No. 1

Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the fuel injector assemblies with plastic bags to prevent damage and contamination.