89221
1.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Make sure that the connecting surfaces are free of foreign matter.
Do not touch the main body ECU (multiplex network body ECU) connector.
| *a | 20° or more |
| *b | Housing Sidewall |
|
Set in this Direction |
Set the main body ECU (multiplex network body ECU) to the position where the guide of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the instrument panel junction block assembly as shown in the illustration.
Make sure to keep the angle at 20° or more as shown in the illustration.
| *a | Housing Sidewall |
|
Slide in this Direction |
Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and engage the guides.
| *a | Side A |
|
Install in this Direction |
While keeping the main body ECU (multiplex network body ECU) in contact with side A of the instrument panel junction block assembly (axis of rotation), lower it as shown in the illustration.
Do not strike or apply excessive force to the side surface of the main body ECU (multiplex network body ECU).
| *1 | Instrument Panel Junction Block Assembly |
| *2 | Main Body ECU (Multiplex Network Body ECU) |
|
Push Area |
Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).
Make sure to press only the push area.
Confirm the engagement of the main body ECU (multiplex network body ECU) and instrument panel junction block assembly by listening for the click sound of the lock engaging.
If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and instrument panel junction block assembly are flush.
82730G
2.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
Engage the clamp to install the instrument panel junction block assembly to the ECU integration box LH
Temporarily install the bolt.
3.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU
| *a | Lock Lever |
Connect the connector.
Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.
Engage the claws.
| *a | Nut (A) |
| *b | Nut (B) |
Engage the claws.
Install the instrument panel junction block assembly with multiplex network body ECU with the 2 bolts and 2 nuts.
Connect the 4 connectors.
for HV Model:
| *a | Lock Lever |
Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.
Engage the clamp.
| *a | Lock Lever |
Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.
Engage the clamp.
Engage the clamps.
Connect the 7 connectors.
55433B
4.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
55550
5.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
55318F
6.INSTALL NO. 2 INSTRUMENT SIDE PANEL
Use the same procedure as for the No. 1 side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION
62312B
7.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
55607
8.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
62112
9.INSTALL COWL SIDE TRIM BOARD LH
67914B
10.INSTALL FRONT DOOR SCUFF PLATE LH
58802E
11.INSTALL FRONT CONSOLE BOX SUB-ASSEMBLY (for 5 Door)
58810J
12.INSTALL CONSOLE BOX ASSEMBLY (for 3 Door)
33554
13.INSTALL SHIFT LEVER CAP (for CVT)
33504F
14.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for CVT)
for TMC Made:
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>SHIFT LEVER KNOB (for TMC Made)>INSTALLATION
for TMMF Made:
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>SHIFT LEVER KNOB (for TMMF Made)>INSTALLATION
33504F
15.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)
55407B
16.INSTALL SWITCH HOLE BASE SUB-ASSEMBLY
55432B
17.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL
55479D
18.INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL GARNISH
19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for 1KR-FE:
Click hereGeneral>MAINTENANCE>1KR-FE AUXILIARY BATTERY>INSTALLATION
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
for G16E-GTS:
Click hereGeneral>MAINTENANCE>G16E-GTS AUXILIARY BATTERY>INSTALLATION
20. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
21. ECU CONFIGURATION
If the main body ECU (multiplex network body ECU) has been replaced, perform ECU configuration.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>ECU CONFIGURATION