Home › Drivetrain › EA67F (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL (for RH Side) › from 2020.09
RM36W0E _52 Drivetrain _095283 EA67F MANUAL TRANSMISSION / TRANSAXLE _0449592 DIFFERENTIAL OIL SEAL(for RH Side) A

EA67F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL(for RH Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the transaxle case oil seal and front dirve shaft oil seal RH removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 36100 1.REMOVE TRANSFER ASSEMBLY

Hide 43457 2.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 31105H 3.REMOVE TRANSAXLE CASE OIL SEAL

a.
C446554C01
1.75,1.031 0.802,0.865 true 0.615,0.781 0.927,0.938 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, pry out the transaxle case oil seal.

HINT:

Tape the screwdriver tip before use.



Hide 43410M 4.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C446555N01
1.417,0.896 1.917,0.979 true 2.958,2.469 2.74,2.958 true 1.094,0.823 1.552,1.021 0.458,0.198 10 false SST 3.01,2.354 3.333,2.563 0.323,0.208 10 false SST

Using SST, remove the front differential case oil seal RH.

SST
09308-00010  

NOTICE:

Be careful not to damage the differential case.



Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Coat the lip of a new front differential case oil seal RH with MP grease.


b.
C448188C01
2.323,0.698 2.792,0.396 true 1.5,3.073 1.813,3.271 0.313,0.198 10 false *a 2.875,0.323 3.333,0.521 0.458,0.198 10 false SST
*a 23.9 to 24.9 mm (0.941 to 0.980 in.)


Using SST and a hammer, tap in a new front differential case oil seal RH to the transaxle case.

SST
09387-52010  

Standard depth:

23.9 to 24.9 mm (0.941 to 0.980 in.)


NOTICE:

Do not damage the front differential case oil seal lip.



Hide 31105H 6.INSTALL TRANSAXLE CASE OIL SEAL

a.

Coat the lip of a new transaxle case oil seal with MP grease.


b.
C446557C01
1.396,2.219 1.396,1.125 true 1.396,1.792 1.125,1.792 1.125,1.792 1.125,1.229 true 2.99,3.052 2.99,2.76 false 2.99,2.875 3.26,2.875 3.26,2.875 3.26,2.354 false 1.292,2.25 1.75,2.448 0.458,0.198 10 false SST 2.875,3.094 3.333,3.292 0.458,0.198 10 false SST 2.51,2.948 2.823,3.146 0.313,0.198 10 false *a
*a 5.0 to 6.0 mm (0.197 to 0.236 in.)


Using SST and a hammer, tap in a new transaxle case oil seal to the transaxle case.

SST
09649-17010  
09950-70010  (09951-07200)

Standard depth:

5.0 to 6.0 mm (0.197 to 0.236 in.)


NOTICE:

Do not damage the transaxle case oil seal lip.



Hide 43457 7.INSTALL DRIVE SHAFT BEARING BRACKET

Hide 36100 8.INSTALL TRANSFER ASSEMBLY

Hide 9. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART