except G16E-GTS:
The clutch switch assembly detects whether the clutch pedal is depressed. If the clutch pedal is depressed, cruise control will be canceled.
for G16E-GTS:
The clutch pedal stroke sensor assembly detects the clutch pedal depression amount. If the clutch pedal is depressed, cruise control will be canceled.
w/o Stop and Start System
w/o Stop and Start System
w/ Stop and Start System
w/ Stop and Start System
Click hereDrivetrain>EA67F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>P080512
Inspect the fuses for circuits related to this system before performing the following procedure.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| except G16E-GTS | A |
| for G16E-GTS | B |
A
B
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Stop and Start System | A |
| w/ Stop and Start System | B |
A
B
Disconnect the A65 clutch switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A65-1 (CL+) - Body ground | Ignition switch ON | 11 to 14 V |
| A65-1 (CL+) - Body ground | Ignition switch off | Below 1 V |
Connect the A65 clutch switch assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for M15A-FKS | A |
| for 1KR-FE | B |
A
B
Disconnect the A65 clutch switch assembly connector.
Disconnect the D51 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D51-45 (D) - A65-2 (CL-) | Always | Below 1 Ω |
| D51-45 (D) - Body ground and other terminals | Always | 10 kΩ or higher |
| A65-2 (CL-) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the D51 ECM connector.
Connect the A65 clutch switch assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A65 clutch switch assembly connector.
Disconnect the A55 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A55-28 (D) - A65-2 (CL-) | Always | Below 1 Ω |
| A55-28 (D) - Body ground and other terminals | Always | 10 kΩ or higher |
| A65-2 (CL-) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the A55 ECM connector.
Connect the A65 clutch switch assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A67 engine stop and start ECU connector.
Disconnect the A65 clutch switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A67-11 (CLU) - A65-2 (CL-) | Always | Below 1 Ω |
| A67-11 (CLU) - Body ground and other terminals | Always | 10 kΩ or higher |
| A65-2 (CL-) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the A65 clutch switch assembly connector
Connect the A67 engine stop and start ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG