Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C050C23  Left Rear Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTC C050C1F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>C050C1F

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C050C23 Left Rear Wheel Speed Sensor Signal Stuck Low Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.*2

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 30 seconds or more.*1

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 15 seconds or more.*2

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 15 seconds or more.*1


·

Rear speed sensor LH (rear axle hub and bearing assembly LH)*2

·

Sensor installation

·

Rear skid control sensor wire LH No. 1*2

·

Rear speed sensor LH*1

·

Rear speed sensor LH (rear axle hub and bearing assembly LH)*2

·

Sensor installation

·

Rear skid control sensor wire LH No. 1*2

·

Wire harness and connector

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)

·

Skid control ECU (brake actuator assembly)


Brake

*1: for AWD

*2: for 2WD


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.


Result:
Result Proceed to
for AWD A
for 2WD B



A

2.CHECK REAR SPEED SENSOR LH INSTALLATION

B

7.CHECK REAR SPEED SENSOR LH INSTALLATION
2.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Rear Speed Sensor LH
*a Correct
*b Incorrect
*c 8.5 Nm
*d No clearance


Turn the ignition switch off.


b.

Check the rear speed sensor LH installation.

OK:

There is no clearance between the rear speed sensor LH and rear axle carrier sub-assembly.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

3.CHECK REAR SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

NG

3.CHECK REAR SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

b.

Check the rear speed sensor LH tip.

OK:

The rear speed sensor LH tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor LH, clean the rear speed sensor LH.

·

If the rear speed sensor LH is damaged, replace the rear speed sensor LH with a new one.




Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (RL WHEEL SPEED)

NG

CLEAN OR REPLACE REAR SPEED SENSOR LH

4.READ VALUE USING GTS (RL WHEEL SPEED)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
RL Wheel Speed
50003 435 16

b.

Drive the vehicle and perform a road test.


c.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (REAR SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (REAR SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A108 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the O117 rear speed sensor LH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O117-2 (RL+) - A108-29 (RL+) Always Below 1 Ω
O117-2 (RL+) or A108-29 (RL+) - Body ground Always 10 kΩ or higher
O117-1 (RL-) - A108-28 (RL-) Always Below 1 Ω
O117-1 (RL-) or A108-28 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK REAR SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK REAR SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)
a.

Remove the component with the rear speed sensor rotor LH.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for TMC Made G16E-GTS)>REMOVAL


b.

Check the rear speed sensor rotor LH.

OK:

The rear speed sensor rotor LH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor rotor LH, clean the rear speed sensor rotor LH.

·

Do not use parts cleaner when cleaning the rear speed sensor rotor LH.

·

If the rear speed sensor rotor LH is damaged, replace the rear speed sensor rotor LH with a new one.



HINT:
·

The rear speed sensor rotor LH is incorporated into the rear axle hub and bearing assembly LH.

·

If the rear speed sensor rotor LH needs to be replaced, replace it together with the rear axle hub and bearing assembly LH.




Result:
Result Proceed to
OK A
NG (The rear speed sensor rotor LH is damaged.) B
NG (There is foreign matter on the rear speed sensor rotor LH.) C



A

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

C

CLEAN REAR SPEED SENSOR ROTOR LH

7.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C210569C18
1.208,1.365 0.979,1.167 false 0.833,1.833 1.25,2.083 0.417,0.25 10 false *b 2.344,1.833 2.677,2.083 0.333,0.25 10 false *c 1.26,1.313 1.594,1.49 0.333,0.177 10 false *a
*a No clearance
*b Correct
*c Incorrect


Turn the ignition switch off.


b.

Check the rear speed sensor LH installation.

OK:

There is no clearance between the rear speed sensor LH and the rear axle hub and bearing assembly LH.


HINT:

The rear speed sensor rotor LH and rear speed sensor LH are incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor rotor LH needs to be replaced, replace the rear axle hub and bearing assembly LH with rear speed sensor LH.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (RL WHEEL SPEED)

NG

CLEAN OR REPLACE REAR SPEED SENSOR RH OR COMPONENT WITH REAR SENSOR ROTOR RH

8.READ VALUE USING GTS (RL WHEEL SPEED)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
RL Wheel Speed
50003 435 16

b.

Drive the vehicle and perform a road test.


c.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

NG

9.INSPECT SKID CONTROL SENSOR WIRE LH
9.INSPECT SKID CONTROL SENSOR WIRE LH
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the j1 and Oj1 skid control sensor wire LH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-2 (RL+) - Oj1-1 (RL+) Always Below 1 Ω
j1-2 (RL+) or Oj1-1 (RL+) - Body ground and other terminals Always 10 kΩ or higher
j1-1 (RL-) - Oj1-3 (RL-) Always Below 1 Ω
j1-1 (RL-) or Oj1-3 (RL-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Oj1-1 (RL+) - A36-29 (RL+) Always Below 1 Ω
Oj1-1 (RL+) or A36-29 (RL+) - Body ground Always 10 kΩ or higher
Oj1-3 (RL-) - A36-28 (RL-) Always Below 1 Ω
Oj1-3 (RL-) or A36-28 (RL-) - Body ground Always 10 kΩ or higher


HINT:

The rear speed sensor LH is incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor LH needs to be replaced, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR