Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C050C1F  Left Rear Wheel Speed Sensor Circuit Intermittent  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C269035E28
1.833,1.083 1.833,0.583 false 1.583,0.583 1.833,0.583 false 5,1.25 5,0.583 false 5,0.583 4.75,0.583 false 0.583,0.167 1.583,0.354 1,0.188 10 false for 2WD: 3.75,0.167 4.917,0.375 1.167,0.208 10 false for AWD: 0.677,0.5 1.75,0.698 1.073,0.198 10 false Speed Sensor 1.25,2.417 2.667,2.667 1.417,0.25 10 false Speed Sensor Rotor 4.833,3.333 5.448,3.583 0.615,0.25 10 false 1.4 V 4.833,3.75 5.448,3.948 0.615,0.198 10 false 0.7 V 3.719,4.208 4.635,4.542 0.917,0.333 10 false High speed 2.771,4.208 3.583,4.542 0.813,0.333 10 false Low speed 4.583,2.5 6,2.75 1.417,0.25 10 false Speed Sensor Rotor 3.833,0.5 4.906,0.698 1.073,0.198 10 false Speed Sensor

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C050C1F Left Rear Wheel Speed Sensor Circuit Intermittent Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less, an open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Rear speed sensor LH*1

·

Rear speed sensor LH (rear axle hub and bearing assembly LH)*2

·

Sensor installation

·

Rear skid control sensor wire LH No. 1*2

·

Wire harness and connector

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)

·

Skid control ECU (brake actuator assembly)


Brake

*1: for AWD

*2: for 2WD


WIRING DIAGRAM

for AWD
C400496E61
5.26,1.021 5.76,1.229 0.5,0.208 10 false RL+ 1.646,1.115 2.083,1.281 0.438,0.167 10 false RL+ 1.646,1.802 2.083,1.99 0.438,0.188 10 false RL- 5.271,1.698 5.719,2 0.448,0.302 10 false RL- 4.917,3 5.427,3.188 0.51,0.188 10 false A108 4.917,3.167 7,3.667 2.083,0.5 10 false Skid Control ECU (Brake Actuator Assembly) 5,1.01 5.333,1.26 0.333,0.25 10 false 29 4.99,1.698 5.281,1.979 0.292,0.281 10 false 28 2.052,1.688 2.385,1.938 0.333,0.25 10 false 1 2.052,1.021 2.385,1.271 0.333,0.25 10 false 2 0.75,2.417 2.333,2.833 1.583,0.417 10 false Rear Speed Sensor LH 0.75,2.25 1.219,2.448 0.469,0.198 10 false O117

for 2WD
C393355E67
0.635,2.24 2.052,2.823 1.417,0.583 10 false Rear Speed Sensor LH (Rear Axle Hub and Bearing Assembly LH) 2.396,2.24 3.521,2.76 1.125,0.521 10 false Skid Control Sensor Wire LH 5.167,3.167 6.698,3.604 1.531,0.438 10 false Skid Control ECU (Brake Actuator Assembly) 5.26,1.021 5.76,1.229 0.5,0.208 10 false RL+ 3.219,1.083 3.667,1.344 0.448,0.26 10 false RL+ 1.646,1.083 2.073,1.323 0.427,0.24 10 false RL+ 2.438,1.083 2.927,1.333 0.49,0.25 10 false RL+ 1.646,1.823 2.063,2.073 0.417,0.25 10 false RL- 2.438,1.833 2.917,2.01 0.479,0.177 10 false RL- 3.229,1.833 3.688,2.021 0.458,0.188 10 false RL- 5.26,1.719 5.646,1.917 0.385,0.198 10 false RL- 2.083,1.115 2.563,1.281 0.479,0.167 10 false j1 2.083,1.802 2.417,2.052 0.333,0.25 10 false j1 3.625,1.115 4.115,1.333 0.49,0.219 10 false Oj1 2.094,1.615 2.396,1.844 0.302,0.229 10 false 1 5.167,3 5.667,3.198 0.5,0.198 10 false A36 2.104,0.917 2.406,1.146 0.302,0.229 10 false 2 3.698,0.917 4,1.146 0.302,0.229 10 false 1 3.698,1.615 4,1.844 0.302,0.229 10 false 3 5,1.01 5.292,1.25 0.292,0.24 10 false 29 5,1.698 5.354,1.948 0.354,0.25 10 false 28 3.625,1.802 4.115,2.021 0.49,0.219 10 false Oj1

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (RL SPEED SENSOR VOLTAGE OPEN)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Chassis > Brake > Data List
Tester Display
RL Speed Sensor Voltage Open
50003 435 113

b.

Select the line graph display.


c.

Check for any momentary interruption in the wire harness and connector.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CHECK FOR INTERMITTENT PROBLEMS

OK:

Normal (There are no momentary interruptions.)


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (RL WHEEL SPEED)

NG

5.CHECK VEHICLE SPECIFICATION
2.READ VALUE USING GTS (RL WHEEL SPEED)
a.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
RL Wheel Speed
50003 435 16

b.

Drive the vehicle and perform a road test.


c.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

10.CHECK REAR SPEED SENSOR LH INSTALLATION
3.CLEAR DTC
a.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

b.

Press the DTC clear button.


c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Result:
Result Proceed to
C050C1F is not output A
C050C1F is output B



A

B

5.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.


Result:
Result Proceed to
for AWD A
for 2WD B



A

6.CHECK REAR SPEED SENSOR LH INSTALLATION

B

10.CHECK REAR SPEED SENSOR LH INSTALLATION
6.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Rear Speed Sensor LH
*a Correct
*b Incorrect
*c 8.5 Nm
*d No clearance


Turn the ignition switch off.


b.

Check the rear speed sensor LH installation.

OK:

There is no clearance between the rear speed sensor LH and rear axle carrier sub-assembly LH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

7.CHECK REAR SPEED SENSOR LH AND REAR SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)

NG

7.CHECK REAR SPEED SENSOR LH AND REAR SPEED SENSOR ROTOR LH (CHECK FOR FOREIGN MATTER)
a.

Remove the rear speed sensor LH and the component with the rear speed sensor rotor LH.



b.

Check the rear speed sensor LH tip and rear speed sensor rotor LH.

OK:

No scratches, oil, or foreign matter on the rear speed sensor LH tip and rear speed sensor rotor LH.


NOTICE:
·

If there is oil or foreign matter on the rear speed sensor LH, clean the rear speed sensor LH.

·

If the rear speed sensor LH is damaged, replace the rear speed sensor LH with a new one.

·

Do not use parts cleaner when cleaning the rear speed sensor rotor LH.

·

If the rear speed sensor rotor LH is damaged, replace the rear speed sensor rotor LH with a new one.



HINT:
·

The rear speed sensor rotor LH is incorporated into the rear axle hub and bearing assembly LH.

·

If the rear speed sensor rotor LH needs to be replaced, replace it together with the rear axle hub and bearing assembly LH.




Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (REAR SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)

NG

CLEAN OR REPLACE REAR SPEED SENSOR LH OR COMPONENT WITH REAR SENSOR ROTOR LH

8.CHECK HARNESS AND CONNECTOR (REAR SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A108 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the O117 rear speed sensor LH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O117-2 (RL+) - A108-29 (RL+) Always Below 1 Ω
O117-2 (RL+) or A108-29 (RL+) - Body ground Always 10 kΩ or higher
O117-1 (RL-) - A108-28 (RL-) Always Below 1 Ω
O117-1 (RL-) or A108-28 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)
a.

Reconnect the A108 skid control ECU (brake actuator assembly) connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O117-2 (RL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

10.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C210569C19
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 false *a 2.344,1.698 2.656,1.896 0.313,0.198 10 false *b 1.344,0.104 1.656,0.302 0.313,0.198 10 false *c
*a Correct
*b Incorrect
*c No clearance


Turn the ignition switch off.


b.

Check the rear speed sensor LH installation.

OK:

There is no clearance between the rear speed sensor LH and the rear axle hub and bearing assembly LH.


HINT:

The rear speed sensor rotor LH and rear speed sensor LH are incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor rotor LH needs to be replaced, replace the rear axle hub and bearing assembly LH with rear speed sensor LH.



Result:
Proceed to
OK
NG



OK

11.INSPECT SKID CONTROL SENSOR WIRE LH

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

11.INSPECT SKID CONTROL SENSOR WIRE LH
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the j1 and Oj1 skid control sensor wire LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-2 (RL+) - Oj1-1 (RL+) Always Below 1 Ω
j1-2 (RL+) or Oj1-1 (RL+) - Body ground and other terminals Always 10 kΩ or higher
j1-1 (RL-) - Oj1-3 (RL-) Always Below 1 Ω
j1-1 (RL-) or Oj1-3 (RL-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)

NG

12.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE LH - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Oj1-1 (RL+) - A36-29 (RL+) Always Below 1 Ω
Oj1-1 (RL+) or A36-29 (RL+) - Body ground Always 10 kΩ or higher
Oj1-3 (RL-) - A36-28 (RL-) Always Below 1 Ω
Oj1-3 (RL-) or A36-28 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)
a.

Reconnect the A36 skid control ECU (brake actuator assembly) connector.


b.

Reconnect the Oj1 skid control sensor wire LH connector.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j1-2 (RL+) - Body ground Ignition switch ON 11 to 14 V


HINT:

The rear speed sensor LH is incorporated into the rear axle hub and bearing assembly LH.

If the rear speed sensor LH needs to be replaced, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG