Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for 3 Door Center Pillar) › from 2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0452657 SIDE AIRBAG SENSOR(for 3 Door Center Pillar) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for 3 Door Center Pillar)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89831 1.INSTALL NO. 1 SIDE AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B598439

Engage the claw to hold the No. 1 side airbag sensor.


d.

Install the No. 1 side airbag sensor with the nut.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)

NOTICE:
·

If the No. 1 side airbag sensor has been dropped, replace it with a new one.

·

When installing the No. 1 side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Tighten the bolt while holding the No. 1 side airbag sensor because the No. 1 side airbag sensor guide is easily damaged.




e.
B598440

Check that there is no looseness in the installation parts of the No. 1 side airbag sensor.


f.
B598438

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



Hide 73220 2.CONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.
B601706N01
2.083,0.313 2.354,0.5 0.271,0.188 10 true (A) 2.115,1.906 2.385,2.094 0.271,0.188 10 true (B)

Engage the guides to connect the front seat outer belt assembly.


b.

Temporarily install the 2 bolts.


c.

Tighten the bolt (A) and then bolt (B).

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (B) : 42 N*m (428 kgf*cm, 31 ft.*lbf)


d.
B601707C01
2.25,0.438 2.469,0.698 false 2.156,0.26 2.469,0.417 0.313,0.156 10 false *1
*1 Locking Button


Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.



Hide 62520B 3.INSTALL QUARTER TRIM PANEL ASSEMBLY

Hide 73220 4.INSTALL FRONT SEAT OUTER BELT ASSEMBLY

Hide 73233 5.INSTALL LAP BELT OUTER ANCHOR COVER

Hide 72693 7.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 8.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 9.INSTALL REAR SEATBACK ASSEMBLY

Hide 10.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 11. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART