| Code | Tester Display | Measurement Item | Trouble Area |
|---|---|---|---|
| X0455 | Steering Angle Sensor Wrong Installation | History of steering angle sensor being installed incorrectly | ·
Correct spiral cable with sensor sub-assembly ·
Steering sensor |
After performing the inspection, check and clear the vehicle control history.
When Steering Angle Sensor Wrong Installation (X0455) is stored, hybrid system output control may operate, but this is not a malfunction.
Using the GTS, perform the Health Check.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
| Proceed to |
|---|
| NEXT |
NEXT
Select the Data List using the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Angle Signal Information | Steering angle value (Rotation to the left side is positive) | Min.: -3070.5 deg, Max.: 3070.5 deg | - | During steering operation: Changes in proportion with steering wheel rotation |
| Tester Display |
|---|
| Steering Angle Signal Information |
Save the internal steering angle value to the GTS memory.
If the value is +/- 360 deg (+/-15 deg), the steering angle sensor was incorrectly installed by 1 rotation.
If the value is +/- 720 deg (+/-15 deg), the steering angle sensor was incorrectly installed by 2 rotations.
In situations other than the above, the steering angle sensor may have been incorrectly installed by 3 or more rotations.
In this case, it is possible that the proper installation or removal procedures were not followed, and the steering angle sensor may have been damaged.
| Result | Proceed to |
|---|---|
| 0 +/- 15 deg | A |
| +/- 360 deg (+/-15 deg) or +/- 720 deg (+/-15 deg) | B |
| None of the above conditions are met | C |
A
B
C
Using the GTS, clear the Vehicle Control History.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect cable from negative (-) auxiliary battery terminal.
If the cable is not disconnected from the negative (-) auxiliary battery terminal, it may not be possible to obtain an accurate steering angle sensor zero point.
Connect cable to negative (-) auxiliary battery terminal.
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
Using the GTS, check for Vehicle Control History.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| X0455 is not output | A |
| X0455 is output | B |
A
B
Remove the spiral cable with sensor sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Be sure to disconnect the cable from the negative (-) auxiliary battery terminal before removing the spiral cable with sensor sub-assembly.
If the cable is not disconnected from the negative (-) auxiliary battery terminal, it may not be possible to obtain an accurate steering angle sensor zero point.
Do not disconnect the steering angle sensor from the spiral cable.
| *a | Interlock |
| *A | Clockwise |
| *B | Counterclockwise |
Based on the internal steering angle value that was saved to the GTS memory earlier, rotate the spiral cable with sensor sub-assembly.
Rotate the steering angle sensor without disconnecting it from the spiral cable.
Make sure to follow the adjustment method shown in the table.
Failure to observe the following precautions may result in damage to the spiral cable with sensor sub-assembly.
When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock to release the interlock.
Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.
Do not forcibly rotate the part.
Make sure to perform the correct number of rotations in the correct direction.
| Steering Angle Signal Information | Correction Method |
|---|---|
| 360 deg (+/-15 deg) | Rotate clockwise (to the right), 1 rotation. |
| - 360 deg (+/-15 deg) | Rotate counterclockwise (to the left), 1 rotation. |
| 720 deg (+/-15 deg) | Rotate clockwise (to the right), 2 rotations. |
| - 720 deg (+/-15 deg) | Rotate counterclockwise (to the left), 2 rotations. |
Install the spiral cable with sensor sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Select the Data List using the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Angle Signal Information | Steering angle value (Rotation to the left side is positive) | Min.: -3070.5 deg, Max.: 3070.5 deg | - | During steering operation:
Changes in proportion with steering wheel rotation. |
| Tester Display |
|---|
| Steering Angle Signal Information |
| Result | Proceed to |
|---|---|
| 0 +/- 15 deg | A |
| None of the above conditions are met | B |
A
B
Using the GTS, clear the Vehicle Control History.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
Using the GTS, check for Vehicle Control History.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| X0455 is not output | A |
| X0455 is output | B |
A
B
Perform steering wheel assembly center position adjustment.
Click hereSteering>STEERING COLUMN>STEERING SYSTEM>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Adjust the alignment (toe) of the wheels.
for Front: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for Rear: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, clear the Vehicle Control History.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect cable from negative (-) auxiliary battery terminal.
If the cable is not disconnected from the negative (-) auxiliary battery terminal, it may not be possible to obtain an accurate steering angle sensor zero point.
Connect cable to negative (-) auxiliary battery terminal.
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
Using the GTS, check for Vehicle Control History.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| X0455 is not output | A |
| X0455 is output | B |
A
B