Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type without TAS Type) › from 2021.04
RM36W0E _56 Audio / Visual / Telematics _088597 AUDIO / VIDEO _0475154 AUDIO AND VISUAL SYSTEM(for Radio and Display Type without TAS Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type without TAS Type)  B1324  Lost Communication with Meter  B1325  Lost Communication with HUD  


DESCRIPTION

These DTCs are stored when communication between the radio and display receiver assembly and combination meter assembly or headup display (meter mirror sub-assembly)* is not possible.

*: w/ Headup Display System


DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter CAN reception error
·

Local bus communication line

·

Combination meter power source circuit

·

Combination meter assembly

·

Radio and display receiver assembly

·

Harness or connector

·

No. 4 global can junction connector (except G16E-GTS)

·

No. 1 global can junction connector (for G16E-GTS)


B1325 Lost Communication with HUD CAN reception error
·

Local bus communication line

·

Headup display (meter mirror sub-assembly) power source circuit

·

Headup display (meter mirror sub-assembly)

·

Radio and display receiver assembly

·

Harness or connector

·

No. 4 global can junction connector (except G16E-GTS)

·

No. 1 global can junction connector (for G16E-GTS)



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

except G16E-GTS
E445982E01
0.177,0.271 1.865,0.688 1.688,0.417 10 false from Engine Stop and Start ECU*1 0.365,1.094 3.729,1.292 3.365,0.198 10 false from IGR-NO. 1 Relay*2 0.49,1.49 3.854,1.688 3.365,0.198 10 false from Auxiliary Battery 2.208,1.25 3.583,1.448 1.375,0.198 10 false METER-IGR 2.073,1.667 4.063,1.865 1.99,0.198 10 false ECU-DCC NO. 2 3.073,0.979 3.385,1.177 0.313,0.198 10 false 38 3.073,1.396 3.385,1.594 0.313,0.198 10 false 22 3.354,1.073 3.813,1.271 0.458,0.198 10 false IG+ 3.365,1.51 3.823,1.708 0.458,0.198 10 false B 3.75,1.073 4.365,1.271 0.615,0.198 10 false MSCH 3.76,1.365 4.375,1.563 0.615,0.198 10 false MSCL 3.948,1.646 4.563,1.844 0.615,0.198 10 false ES 4.271,0.948 4.583,1.146 0.313,0.198 10 false 27 4.26,1.229 4.573,1.427 0.313,0.198 10 false 10 4.271,1.542 4.583,1.74 0.313,0.198 10 false 23 4.563,0.948 4.875,1.146 0.313,0.198 10 false 11 4.573,1.229 4.885,1.427 0.313,0.198 10 false 22 5.563,1.229 5.875,1.427 0.313,0.198 10 false 21 5.552,0.948 5.865,1.146 0.313,0.198 10 false 10 5.948,0.958 6.26,1.156 0.313,0.198 10 false 5 5.948,1.229 6.26,1.427 0.313,0.198 10 false 6 6.125,1.073 6.74,1.271 0.615,0.198 10 false CNH1 6.125,1.354 6.74,1.552 0.615,0.198 10 false CNL1 5.906,1.677 6.365,1.875 0.458,0.198 10 false H80 5.896,1.833 7.094,2.24 1.198,0.406 10 false Radio and Display Receiver Assembly 3.219,1.979 3.677,2.177 0.458,0.198 10 false H6 3.219,2.135 4.406,2.531 1.188,0.396 10 false Combination Meter Assembly 0.167,2.271 1.875,2.646 1.708,0.375 10 false from Engine Stop and Start ECU*1 3.917,2.906 4.531,3.104 0.615,0.198 10 false TX+ 3.917,3.208 4.531,3.406 0.615,0.198 10 false TX- 3.927,3.615 4.542,3.813 0.615,0.198 10 false ES 4.25,2.792 4.563,2.99 0.313,0.198 10 false 14 4.25,3.073 4.563,3.271 0.313,0.198 10 false 15 4.271,3.479 4.427,3.677 0.156,0.198 10 false 4 4.625,2.792 4.781,2.99 0.156,0.198 10 false 9 4.573,3.073 4.885,3.271 0.313,0.198 10 false 20 3.344,3.083 3.802,3.281 0.458,0.198 10 false IG 3.344,4.604 3.802,4.802 0.458,0.198 10 false B 3.125,3 3.281,3.198 0.156,0.198 10 false 1 3.135,4.5 3.292,4.698 0.156,0.198 10 false 2 0.375,3.083 3.74,3.281 3.365,0.198 10 false from IGR-NO. 1 Relay*2 0.375,4.594 3.74,4.792 3.365,0.198 10 false from Auxiliary Battery*2 0.177,3.771 1.875,4.208 1.698,0.438 10 false from Engine Stop and Start ECU*1 2.063,4.76 4.052,4.958 1.99,0.198 10 false ECU-DCC NO. 2 2.135,3.26 4.125,3.458 1.99,0.198 10 false ECU-IGR NO. 1 3.073,4.948 3.531,5.146 0.458,0.198 10 false H61 3.073,5.104 4.542,5.552 1.469,0.448 10 false Headup Display (Meter Mirror Sub-assembly)*3 4.458,5.583 5.073,5.781 0.615,0.198 10 false H115 4.458,5.76 6.927,6.052 2.469,0.292 10 false No. 4 Global Can Junction Connector 0.25,5.167 4.531,5.365 4.281,0.198 10 false *1: w/ Stop and Start System 0.25,5.583 4.531,5.781 4.281,0.198 10 false *2: w/o Stop and Start System 0.25,6 4.531,6.198 4.281,0.198 10 false *3: w/ Headup Display System 0.802,6.344 5.385,6.542 4.583,0.198 10 false : Local Bus Communication Line

for G16E-GTS
E450872E01
0.177,1.073 1.865,1.49 1.688,0.417 10 false from Engine Stop and Start ECU 0.563,1.813 3.927,2.01 3.365,0.198 10 false from Auxiliary Battery 2.156,1.99 4.146,2.188 1.99,0.198 10 false ECU-DCC NO. 2 3.073,0.979 3.385,1.177 0.313,0.198 10 false 38 3.125,1.698 3.438,1.896 0.313,0.198 10 false 22 3.354,1.073 3.813,1.271 0.458,0.198 10 false IG+ 3.365,1.854 3.823,2.052 0.458,0.198 10 false B 3.75,1.073 4.365,1.271 0.615,0.198 10 false MSCH 3.76,1.365 4.375,1.563 0.615,0.198 10 false MSCL 3.969,1.99 4.583,2.188 0.615,0.198 10 false ES 4.271,0.948 4.583,1.146 0.313,0.198 10 false 27 4.26,1.229 4.573,1.427 0.313,0.198 10 false 10 4.292,1.854 4.604,2.052 0.313,0.198 10 false 23 4.563,0.948 4.875,1.146 0.313,0.198 10 false 11 4.573,1.229 4.885,1.427 0.313,0.198 10 false 22 5.563,1.229 5.875,1.427 0.313,0.198 10 false 21 5.552,0.948 5.865,1.146 0.313,0.198 10 false 10 5.948,0.958 6.26,1.156 0.313,0.198 10 false 5 5.948,1.229 6.26,1.427 0.313,0.198 10 false 6 6.125,1.073 6.74,1.271 0.615,0.198 10 false CNH1 6.125,1.354 6.74,1.552 0.615,0.198 10 false CNL1 5.906,1.677 6.365,1.875 0.458,0.198 10 false H80 5.896,1.833 7.094,2.24 1.198,0.406 10 false Radio and Display Receiver Assembly 3.24,2.333 3.698,2.531 0.458,0.198 10 false H6 3.229,2.521 4.417,2.917 1.188,0.396 10 false Combination Meter Assembly 3.948,3.552 4.563,3.75 0.615,0.198 10 false TX+ 3.958,3.844 4.573,4.042 0.615,0.198 10 false TX- 3.969,4.198 4.583,4.396 0.615,0.198 10 false ES 4.281,3.417 4.594,3.615 0.313,0.198 10 false 14 4.281,3.719 4.594,3.917 0.313,0.198 10 false 15 4.281,4.052 4.438,4.25 0.156,0.198 10 false 4 4.625,3.417 4.781,3.615 0.156,0.198 10 false 9 4.573,3.719 4.885,3.917 0.313,0.198 10 false 20 3.365,3.729 3.823,3.927 0.458,0.198 10 false IG 3.344,4.604 3.802,4.802 0.458,0.198 10 false B 3.146,3.552 3.302,3.75 0.156,0.198 10 false 1 3.135,4.5 3.292,4.698 0.156,0.198 10 false 2 0.375,4.688 3.74,4.885 3.365,0.198 10 false from Auxiliary Battery 0.177,3.771 1.875,4.208 1.698,0.438 10 false from Engine Stop and Start ECU 2.135,4.865 4.125,5.063 1.99,0.198 10 false ECU-DCC NO. 2 3.073,5.177 3.531,5.375 0.458,0.198 10 false H61 3.052,5.365 4.521,5.813 1.469,0.448 10 false Headup Display (Meter Mirror Sub-assembly)* 4.594,5.615 5.208,5.813 0.615,0.198 10 false H145 4.583,5.802 6.219,6.333 1.635,0.531 10 false No. 1 Global Can Junction Connector 0.25,5.906 4.531,6.104 4.281,0.198 10 false *: w/ Headup Display System 0.802,6.344 5.385,6.542 4.583,0.198 10 false : Local Bus Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
except G16E-GTS A
for G16E-GTS B



A

2.CHECK DTC

B

34.CHECK DTC
2.CHECK DTC
a.

Check for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTC B1324 and B1325 are not output A
DTC B1324 and B1325 are output B
DTC B1324 is output C
DTC B1325 is output D



A

B

3.CHECK LOCAL BUS

C

12.CHECK VEHICLE TYPE

D

23.CHECK VEHICLE TYPE
3.CHECK LOCAL BUS
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (Below 54 Ω) B
NG (70 Ω or higher) C



A

B

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

C

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-11 - H115-22 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-9 - H115-20 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

7.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
7.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H61 headup display (meter mirror sub-assembly) connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-14 (TX+) - H61-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H6 combination meter assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-27 (MSCH) - H6-10 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Connect the H80 radio and display receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)

B

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)
13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-23 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-22 (B) - Body ground Ignition switch off 11 to 14 V
H6-38 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Connect the H6 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-11 - H115-22 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
15.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

16.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
16.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H6 combination meter assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-27 (MSCH) - H6-10 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-23 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-22 (B) - Body ground Ignition switch off 11 to 14 V
H6-38 (IG+) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Connect the H6 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-11 - H115-22 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

22.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
20.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

21.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
21.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H6 combination meter assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-27 (MSCH) - H6-10 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

24.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)

B

29.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)
24.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)
a.

Disconnect the H61 headup display (meter mirror sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-4 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H61-2 (B) - Body ground Ignition switch off 11 to 14 V
H61-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Connect the H61 headup display (meter mirror sub-assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-9 - H115-20 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

28.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
26.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

27.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
27.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H61 headup display (meter mirror sub-assembly) connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-14 (TX+) - H61-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)
a.

Disconnect the H61 headup display (meter mirror sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-4 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H61-2 (B) - Body ground Ignition switch off 11 to 14 V
H61-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

30.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

30.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Connect the H61 headup display (meter mirror sub-assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-9 - H115-20 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

31.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

33.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
31.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

32.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
32.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H61 headup display (meter mirror sub-assembly) connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-14 (TX+) - H61-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.CHECK DTC
a.

Check for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTC B1324 and B1325 are not output A
DTC B1324 and B1325 are output B
DTC B1324 is output C
DTC B1325 is output D



A

B

35.CHECK LOCAL BUS

C

44.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)

D

49.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)
35.CHECK LOCAL BUS
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H145-10 - H145-21 Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (Below 54 Ω) B
NG (70 Ω or higher) C



A

B

36.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

C

42.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
36.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H145 No. 1 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H145-10 - H145-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

37.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

41.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
37.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H145 No. 1 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H145-11 - H145-22 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

38.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

40.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
38.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H145 No. 1 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H145-9 - H145-20 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

39.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
39.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H61 headup display (meter mirror sub-assembly) connector.


c.

Connect the H145 No. 1 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-14 (TX+) - H61-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H6 combination meter assembly connector.


c.

Connect the H145 No. 1 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-27 (MSCH) - H6-10 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Connect the H145 No. 1 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

43.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
43.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H145 No. 1 global can junction connector.


c.

Connect the H80 radio and display receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H145-10 - H145-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

44.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-23 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-22 (B) - Body ground Ignition switch off 11 to 14 V
H6-38 (IG+) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

45.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

45.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H145 No. 1 global can junction connector.


c.

Connect the H6 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H145-11 - H145-22 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

46.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

48.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
46.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H145 No. 1 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H145-10 - H145-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

47.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
47.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Connect the H145 No. 1 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

48.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H6 combination meter assembly connector.


c.

Connect the H145 No. 1 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-27 (MSCH) - H6-10 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

49.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)
a.

Disconnect the H61 headup display (meter mirror sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-4 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H61-2 (B) - Body ground Ignition switch off 11 to 14 V
H61-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

50.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

50.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H145 No. 1 global can junction connector.


c.

Connect the H61 headup display (meter mirror sub-assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H145-9 - H145-20 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

51.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)

NG

53.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
51.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H145 No. 1 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H145-10 - H145-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 GLOBAL CAN JUNCTION CONNECTOR

NG

52.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
52.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Connect the H145 No. 1 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

53.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 1 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H61 headup display (meter mirror sub-assembly) connector.


c.

Connect the H145 No. 1 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-14 (TX+) - H61-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR