Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type) › from 2021.04
RM36W0E _56 Audio / Visual / Telematics _088597 AUDIO / VIDEO _0475155 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type)  Mute Signal Circuit between Radio Receiver and Telematics Transceiver  


DESCRIPTION

The telephone transceiver assembly sends a mute signal to the radio and display receiver assembly.

The radio and display receiver assembly controls the volume according to the mute signal from the telephone transceiver assembly.

WIRING DIAGRAM

E463258E02
1.26,1.698 2.896,1.917 1.635,0.219 10 false H80 1.24,1.865 2.927,2.271 1.688,0.406 10 false Radio and Display Receiver Assembly 4.354,1.052 4.594,1.26 0.24,0.208 10 false 14 2.604,1.052 2.833,1.24 0.229,0.188 10 false 3 2.115,1.146 2.573,1.344 0.458,0.198 10 false TMUT 4.646,1.167 5.135,1.365 0.49,0.198 10 false MUTE 4.208,1.677 4.667,1.875 0.458,0.198 10 false H85 4.208,1.844 6.365,2.094 2.156,0.25 10 false Telephone Transceiver Assembly

CAUTION / NOTICE / HINT

HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type)>PRECAUTION


PROCEDURE

1.INSPECT TELEPHONE TRANSCEIVER ASSEMBLY
a.
E442862C06
1.521,0.594 2.021,0.844 0.5,0.25 1.052,1.698 0.781,0.99 true 1.625,0.625 2.052,0.854 0.427,0.229 10 false H85 0.604,0.781 1.052,1.021 0.448,0.24 10 false MUTE 0.198,0.177 0.51,0.375 0.313,0.198 10 false *a
*a Component with harness connected
(Telephone Transceiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H85-14 (MUTE) - Body ground Ignition switch ACC
Audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the H85 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-3 (TMUT) - H85-14 (MUTE) Always Below 1 Ω
H80-3 (TMUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the H85 telephone transceiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H85-14 (MUTE) - Body ground Ignition switch ACC 2.0 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY