Home › Engine / Hybrid System › M15A-FXE (FUEL) › FUEL TANK › from 2021.11
RM36W0E _51 Engine / Hybrid System _088661 M15A-FXE FUEL _0427240 FUEL TANK A

M15A-FXE FUEL  FUEL TANK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Gas leaks from exhaust system is repaired Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

a.
A465605C01
0.958,0.333 1.323,0.531 false 0.771,0.24 1.083,0.438 0.313,0.198 10 false *a
*a Cord


When removing and storing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using a cord or similar.

NOTICE:

Depending on the arrangement of the inlet hose during storage, the inlet hose and rear suspension may interfere and cause fuel leakage.



Hide 2.DRAIN FUEL

Hide 3.REMOVE WHEEL ASSEMBLY

Hide 52592 4.REMOVE REAR BUMPER SIDE SEAL LH (for TMMF, TMMCZ Made)

Hide 65638 5.REMOVE REAR WHEEL HOUSE LINER LH (for TMMF, TMMCZ Made)

a.

Remove the 2 screws.

A466960


b.

Remove the 10 clips.


c.
A466961

Remove the grommet and rear fender liner.


Hide 65638 6.SEPARATE REAR WHEEL HOUSE LINER LH (for TMC Made)

a.

Remove the 2 screws.

A457035


b.

Remove the 5 clips.


c.

Remove the grommet and separate the rear fender liner.


Hide 77020A 7.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 77310A 8.REMOVE FUEL TANK CAP ASSEMBLY

Hide 51447D 9.REMOVE NO. 4 CENTER ENGINE UNDER COVER (for TMMF, TMMCZ Made)

Hide 51447D 10.REMOVE NO. 4 CENTER ENGINE UNDER COVER (for TMC Made)

Hide 17410 11.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 77606 12.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A457043

Remove the 3 clips and No. 1 fuel tank protector sub-assembly from the fuel tank assembly.


Hide 77027B 13.DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY

a.
A465984

Disconnect the No. 1 fuel emission tube sub-assembly from the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209F 14.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A465985

Disconnect the fuel tank main tube sub-assembly from the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 58415Q 15.REMOVE NO. 1 REAR FLOOR BOARD (for TMMF, TMMCZ Made)

Hide 77730C 16.DISCONNECT NO. 2 CHARCOAL CANISTER ASSEMBLY (for TMMF, TMMCZ Made)

a.
A466957

Disconnect the canister air tube from the No. 2 canister.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION


b.
A468076

Disengage the clamp to separate the No. 1 canister outlet hose sub-assembly from the fuel tank assembly.


Hide 17.DISCONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY (for TMMF, TMMCZ Made)

a.

Remove the bolt.

A466959


b.

Disengage the 2 clamps.


c.

Disengage the locations shown in the illustration, and disengage the fuel tank filler pipe sub-assembly from the vehicle body.


Hide 18.DISCONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY (for TMC Made)

a.

Remove the bolt.

A465233


b.

Disengage the locations shown in the illustration, and disengage the fuel tank filler pipe sub-assembly from the vehicle body.


Hide 77100U 19.REMOVE FUEL TANK ASSEMBLY

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.
A465986

Support the fuel tank assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.
A465987

Remove the 4 bolts.


c.

Lower the engine lifter to remove the fuel tank assembly.

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




Hide 77209F 20.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A465988

Disengage the 3 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.


Hide 77027B 21.REMOVE NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY

a.
A465989

Disengage the 4 clamps to remove the No. 1 fuel emission tube sub-assembly from the fuel tank assembly.


Hide 77217A 22.REMOVE NO. 2 FUEL TANK FILLER PIPE SUPPORT

a.
A465236

Disengage the 2 claws to remove the No. 2 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.


Hide 77216A 23.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT (for TMMF, TMMCZ Made)

a.
A466963

Disengage the 2 clamps to remove the No. 1 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.


Hide 77216A 24.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT (for TMC Made)

a.
A465237

Disengage the 3 clamps to remove the No. 1 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.


Hide 77218A 25.REMOVE NO. 3 FUEL TANK FILLER PIPE SUPPORT (for TMMF, TMMCZ Made)

a.
A466964

Disengage the 2 clamps to remove the No. 3 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.


Hide 77218A 26.REMOVE NO. 3 FUEL TANK FILLER PIPE SUPPORT (for TMC Made)

a.
A465990

Disengage the 3 clamps to remove the No. 3 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.


Hide 77277R 27.REMOVE FUEL TANK FILLER PIPE PROTECTOR (for TMMF, TMMCZ Made)

a.

Disengage the 3 claws.

A466965


b.

Disengage the 3 clamps to remove the fuel tank filler pipe protector from the fuel tank filler pipe sub-assembly.


Hide 77277R 28.REMOVE FUEL TANK FILLER PIPE PROTECTOR (for TMC Made)

a.

Disengage the 4 claws.

A458633


b.

Disengage the 4 clamps to remove the fuel tank filler pipe protector from the fuel tank filler pipe sub-assembly.