| Symptom | Trouble Area |
|---|---|
| There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen. | ·
CAN main bus line, CAN branch line or connector ·
Central gateway ECU (network gateway ECU) ·
Option connector (bus buffer ECU) ·
CAN compatible optional devices ·
Radio and display receiver assembly (for Radio and Display Type with TAS Type) ·
No. 11 global CAN junction connector |
for TMC Made
for TMMF, TMMCZ Made
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.
Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-5 (CA8H) - H40-6 (CA8L) | Cable disconnected from negative (-) auxiliary battery terminal | Below 70 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-5 (CA8H) - H40-6 (CA8L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-5 (CA8H) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-6 (CA8L) - H3-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-5 (CA8H) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-6 (CA8L) - H3-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF, TMMCZ Made | B |
A
B
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-5 (CA8H) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-6 (CA8L) - H3-4 (CG) |
Reconnect the central gateway ECU (network gateway ECU) connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 option connector (bus buffer ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H62-2 (CAN+) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H62-1 (CAN-) - H3-4 (CG) |
Reconnect the option connector (bus buffer ECU) connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H151 No. 11 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-1 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H151-12 (CANL) - H3-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-3 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H151-14 (CANL) - H3-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| for Radio and Display Type with TAS Type | A |
| except Radio and Display Type with TAS Type | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-4 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H151-15 (CANL) - H3-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-2 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H151-13 (CANL) - H3-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-1 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H151-12 (CANL) - H3-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-3 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H151-14 (CANL) - H3-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Disconnect the H80 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-4 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H151-15 (CANL) - H3-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 option connector (bus buffer ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-2 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H151-15 (CANL) - H3-4 (CG) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF, TMMCZ Made | B |
A
B
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-5 (CA8H) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-6 (CA8H) - H3-16 (BAT) |
Reconnect the central gateway ECU (network gateway ECU) connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 option connector (bus buffer ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H62-2 (CAN+) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H62-1 (CAN-) - H3-16 (BAT) |
Reconnect the option connector (bus buffer ECU) connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H151 No. 11 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-1 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H151-12 (CANL) - H3-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-3 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H151-14 (CANL) - H3-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| for Radio and Display Type with TAS Type | A |
| except Radio and Display Type with TAS Type | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-4 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H151-15 (CANL) - H3-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-2 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H151-13 (CANL) - H3-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-1 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H151-12 (CANL) - H3-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-3 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H151-14 (CANL) - H3-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Disconnect the H80 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-4 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H151-15 (CANL) - H3-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 option connector (bus buffer ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-2 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H151-13 (CANL) - H3-16 (BAT) |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF, TMMCZ Made | B |
A
B
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-5 (CA8H) - H40-6 (CA8L) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
Reconnect the central gateway ECU (network gateway ECU) connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 option connector (bus buffer ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H62-2 (CAN+) - H62-1 (CAN-) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
Reconnect the option connector (bus buffer ECU) connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H151 No. 11 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-1 (CANH) - H151-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-3 (CANH) - H151-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| for Radio and Display Type with TAS Type | A |
| except Radio and Display Type with TAS Type | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-4 (CANH) - H151-15 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-2 (CANH) - H151-13 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-1 (CANH) - H151-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-3 (CANH) - H151-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Disconnect the H80 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-4 (CANH) - H151-15 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 option connector (bus buffer ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-2 (CANH) - H151-13 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF, TMMCZ Made | B |
A
B
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-5 (CA8H) - H40-6 (CA8L) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
Reconnect the central gateway ECU (network gateway ECU) connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H62 option connector (bus buffer ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H62-2 (CAN+) - H62-1 (CAN-) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
Reconnect the option connector (bus buffer ECU) connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H151 No. 11 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-1 (CANH) - H151-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-3 (CANH) - H151-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-1 (CANH) - H40-5 (CA8H) | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| H151-12 (CANL) - H40-6 (CA8L) |
| Result |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H151-3 (CANH) - H40-33 (CAYH) | Cable disconnected from negative (-) auxiliary battery terminal | Below 1 Ω |
| H151-14 (CANL) - H40-34 (CAYL) |
| Result |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG