Home › Power Source / Network › NETWORKING › NETWORK GATEWAY ECU (for LHD) › from 2020.09
RM36W0E _57 Power Source / Network _088060 NETWORKING _0432669 NETWORK GATEWAY ECU(for LHD) A

NETWORKING  NETWORK GATEWAY ECU(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the horn button assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Central gateway ECU (network gateway ECU) Update ECU security key - (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55479E 3.REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55432B 4.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL

Hide 55407B 5.REMOVE SWITCH HOLE BASE SUB-ASSEMBLY

Hide 33504F 6.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for CVT)

Hide 33504F 7.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

Hide 33554 8.REMOVE SHIFT LEVER CAP (for CVT)

Hide 58810J 9.REMOVE FRONT CONSOLE BOX SUB-ASSEMBLY (for 5 Door)

Hide 58810J 10.REMOVE CONSOLE BOX ASSEMBLY (for 3 Door)

Hide 67913B 11.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 5 Door)>REMOVAL


Hide 62111C 12.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 5 Door)>REMOVAL


Hide 55607 13.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62311B 14.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55317E 15.REMOVE NO. 1 INSTRUMENT SIDE PANEL

Hide 55550 16.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 55433B 17.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 82878 18.REMOVE ECU INTEGRATION BOX RH

a.
B579407

Disengage clamps and disconnect the 7 connectors.


b.
B579408

Remove the bolt and 2 nuts.


c.

Disengage the claws to remove the ECU integration box RH.


Hide 89111 19.REMOVE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

a.
B579405C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the central gateway ECU (network gateway ECU) as shown in the illustration.

NOTICE:
·

If the ECU integration box LH is deformed or damaged, replace it.

·

Do not bend the claws more than necessary.