Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › from 2021.11
RM36W0E _52 Drivetrain _088636 P910 HYBRID TRANSMISSION / TRANSAXLE _0421988 HYBRID VEHICLE TRANSAXLE A

P910 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Engine assembly

·

Air fuel ratio sensor

·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF, TMMCZ Made:
(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
(Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PERFORM RESOLVER INITIALIZATION

NOTICE:

If it is necessary to replace the hybrid vehicle transaxle assembly, make sure to perform resolver initialization before starting work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>UTILITY


Hide 2.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 82121 4.DISCONNECT ENGINE WIRE

a.
C435097

Disengage the 6 clamps.


b.
C429027C01
2.635,1.24 2.844,1.438 0.208,0.198 10 true *1 0.802,1.75 1.021,1.906 0.219,0.156 10 true *2 2.094,0.375 2.281,0.573 0.188,0.198 10 true *3
*1 Resolver (Transmission Fluid Temperature Sensor) Connector
*2 Shift Lever Position Sensor Connector
*3 Generator Temperature Sensor Connector


Disengage the clamp.


c.

Remove the bolt.


d.

Disconnect the resolver (transmission fluid temperature sensor) connector.


e.

Disconnect the shift lever position sensor connector.

NOTICE:
C438726

After disconnecting the engine wire, cover the connector of the shift lever position sensor with tape (non-residue type) or equivalent to prevent the entry of foreign matter or water.



f.

Disconnect the generator temperature sensor connector.


Hide 821H2 5.REMOVE HV AIR CONDITIONING WIRE

a.
C429029

Remove the 2 bolts to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.


b.
C429030

Disengage the clamp.


c.
C429031C01
1.333,1.604 1.667,1.448 true 1.698,1.333 2.01,1.531 0.313,0.198 10 false *a
*a Green-colored Lock
V100137

Slide


Using a screwdriver, slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the connector.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Insulate the disconnected terminals and connector with insulating tape.



Hide 28193 6.REMOVE STARTER HOLE INSULATOR

a.
C429033

Remove the 2 bolts and starter hole insulator from the engine assembly.


Hide 11363A 7.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
C429035

Remove the flywheel housing side cover from the engine assembly.


Hide 16290F 8.SEPARATE NO. 3 WATER BY-PASS HOSE ASSEMBLY

a.
C429037

Disengage the clamp to separate the No. 3 water by-pass hose from the hybrid vehicle transaxle assembly.


Hide 9.REMOVE ENGINE ASSEMBLY

a.
C429039

Remove the 7 bolts and engine assembly from the hybrid vehicle transaxle assembly.

NOTICE:
·

To avoid damaging the knock pins, do not pry between the hybrid vehicle transaxle assembly and engine assembly.

·

To prevent the splines of the transmission input damper assembly from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper assembly during engine assembly removal and installation.




Hide 51201 10.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C435098

Remove the bolt and front suspension crossmember sub-assembly from the No. 2 engine moving control rod.


Hide 12364B 11.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C429046

Remove the 3 bolts and No. 2 engine moving control rod from the hybrid vehicle transaxle assembly.


Hide G125A 13.REMOVE MOTOR COOLING COOLER

a.
C429048

Slide the clip and disconnect the No. 1 motor cooling hose from the No. 1 motor cooling pipe.


b.
C429049

Remove the oil cooler union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.


c.

Disengage the clamp.


d.
C429050

Remove the 3 bolts and motor cooling cooler with No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.

NOTICE:

Make sure not to remove the No. 1 motor cooling hose and No. 2 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.



Hide G1251B 14.REMOVE NO. 1 MOTOR COOLING PIPE

a.
C429055

Loosen the flare nut of the No. 1 motor cooling pipe and disconnect the No. 1 motor cooling pipe from the union.


b.
C429056

Remove the bolt, No. 2 oil cooler tube clamp and No. 1 motor cooling pipe from the No. 1 transmission control cable bracket.


Hide 44781E 15.REMOVE HOSE BRACKET

a.
C429060

Remove the bolt and hose bracket from the hybrid vehicle transaxle assembly.


Hide 33823 16.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C429062

Remove the bolt and No. 1 transmission control cable bracket from the hybrid vehicle transaxle assembly.


Hide 17.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C429064

Remove the 2 bolts and 2 wire harness clamp brackets from the hybrid vehicle transaxle assembly.


Hide 18.REMOVE STUD BOLT

a.
C429072

Using a E8 "TORX" socket wrench, remove the 2 stud bolts from the hybrid vehicle transaxle assembly.


Hide 19.REMOVE TRANSAXLE HOUSING PLUG

HINT:

Perform this procedure only when replacement of the transaxle housing plug or gasket is necessary.


a.
C429066

Remove the transaxle housing plug and gasket from the hybrid vehicle transaxle assembly.


Hide 30900N 20.REMOVE TRANSAXLE BREATHER PLUG

HINT:

Perform this procedure only when replacement of the transaxle breather plug is necessary.


a.
C429068

Remove the transaxle breather plug from the hybrid vehicle transaxle assembly.


Hide 21.REMOVE UNION

HINT:

Perform this procedure only when replacement of the union or O-ring is necessary.


a.
C429070

Remove the union and O-ring from the hybrid vehicle transaxle assembly.