Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2021.11
RM36W0E _51 Engine / Hybrid System _089412 M15A-FXE ENGINE MECHANICAL _0424638 ENGINE ASSEMBLY A

M15A-FXE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Replacement of engine assembly

·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF, TMMCZ Made:
(Click here)
Suspension, tires, etc.*2
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
·
A340377C22
0.542,1.115 0.958,1.115 false 0.344,1.01 0.656,1.208 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the engine lifter


Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.


·
A340359C12
0.375,1.135 0.75,1.281 true 0.135,1.031 0.448,1.229 0.313,0.198 10 false *a
*a High temperature areas


Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.

·

Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.


·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.REMOVE FRONT WHEELS

Hide 51451A 6.REMOVE CENTER ENGINE UNDER COVER (w/ Cover)

Hide 51447D 9.REMOVE NO. 4 CENTER ENGINE UNDER COVER

Hide 11.DRAIN ENGINE COOLANT (for Engine)

Hide G9200 13.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 82662A 14.REMOVE NO. 1 RELAY BLOCK COVER

a.
A458186

Remove the No. 1 relay block cover from the engine room relay block.


Hide 15.REMOVE ENGINE WIRE

a.
A466041

Disconnect the 2 connectors from the engine room relay block.


b.

Remove the nut.


c.

Disengage the 4 claws to separate the engine wire from the engine room relay block.


d.
A486022

Remove the 2 bolts to separate the engine wire from the vehicle.


e.

Remove the clamp.


f.
A464800

Disengage the clamp to separate the engine wire from the vehicle.


Hide 33820B 16.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C429508

Disengage the clamp to separate the transmission control cable assembly.


b.

Remove the bolt to disconnect the transmission control cable assembly from the hybrid vehicle transaxle assembly.


c.
A464801

Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.


d.

Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


Hide 16571C 17.DISCONNECT NO. 1 RADIATOR HOSE

a.
A464802

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16572D 18.DISCONNECT NO. 2 RADIATOR HOSE

a.
A464803

Slide the clip and disconnect the No. 2 radiator hose from the water inlet sub-assembly.


Hide G922H 19.DISCONNECT INLET HYBRID RADIATOR HOSE

a.
A464804

Slide the clip and disconnect the inlet hybrid radiator hose from the motor cooling cooler.


Hide G922F 20.DISCONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

a.
A464805

Slide the clip and disconnect the outlet No. 1 hybrid water pump hose from the motor cooling cooler.


Hide 23826 21.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A464806

Disconnect the No. 1 fuel vapor feed hose from the fuel tank to canister tube.


Hide 77261D 22.DISCONNECT FUEL TANK TO CANISTER TUBE

a.
A464807

Disengage the clamps to separate the fuel tank to canister tube from the engine wire.


Hide 16290F 23.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

Hide 87245 24.DISCONNECT INLET HEATER WATER HOSE

Hide 23901 25.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A459849

Remove the No. 1 fuel pipe clamp for the fuel tube sub-assembly.


b.
A459851

Disconnect the fuel tube sub-assembly from the fuel pump assembly.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 88711 26.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 88704 27.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 45259A 29.REMOVE COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 30.REMOVE COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 45260 31.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 17410 32.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 34.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.
A464808

Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


c.
A464809

Remove the bolt and engine mounting stay LH.


d.
A464810

Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.


e.
A458197

Remove the 10 bolts to separate the front suspension crossmember sub-assembly from the vehicle.


f.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 12353 35.REMOVE ENGINE MOUNTING BRACKET CAP

a.
A466042

Turn over the engine mounting bracket cap to the upper part.


b.
A466043

While rotating in the direction shown in the diagram, remove the engine mounting bracket cap.


Hide 36.INSTALL ENGINE HANGER

a.
A458200C01
0.313,0.667 0.646,0.667 true 2.167,0.667 2.5,0.667 true 0.135,0.573 0.323,0.75 0.188,0.177 10 false *1 1.958,0.583 2.146,0.76 0.188,0.177 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger
V100135

Bolt


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-25030
No. 2 Engine Hanger 12282-25010
Bolt 91552-F1040



b.

Attach an engine sling device and hang the engine assembly with transaxle with a chain block.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedure while the engine assembly with transaxle is suspended because doing so may cause the engine assembly with transaxle to drop, resulting in injury. However, the engine assembly with transaxle needs to be suspended when it is installed to or removed from an engine stand.




Hide 12372A 37.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A464811

Remove the 5 bolts, nut and engine mounting insulator LH from the vehicle.


Hide G92A0A 38.DISCONNECT INVERTER RESERVE TANK ASSEMBLY

a.
A464812

Remove the 2 bolts and disconnect the inverter reserve tank assembly.


Hide 12305 39.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A464813

Remove the clamp and disconnect the air conditioner tube.


b.

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.


Hide 11363A 41.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 82121 43.REMOVE ENGINE WIRE

a.
A458206

Remove the 6 bolts.


b.
A464815

Remove the bolt.


c.
A464814

Remove the 3 bolts.


d.

Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.


Hide 44.REMOVE WATER HOSE

a.
A464816

Slide the 3 clips and remove the water hose from the engine assembly with transaxle.


Hide 31270 46.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 19315 48.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 88370 49.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

Hide 50.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 51.REMOVE ENGINE HANGER

a.

Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.