2005-2008 Yaris · Service Manual BRAKE

C1241/41 Low Battery Positive Voltage or Abnormally High Battery Positive Voltage

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

When there is an abnormality in the power supply circuit of the brake actuator (skid control ECU), the skid control ECU sets a DTC and the operation is prohibited by the fail-safe function. This DTC is set when the voltage supplied to terminal IG1 is outside the DTC detection threshold, due to abnormalities of the battery, power source circuits or charging circuits such as the alternator circuit.
The fail-safe function is canceled when the voltage to terminal IG1 returns to normal.
DTC No.
DTC Detecting Conditions
Trouble Areas
C1241/41
When any of following conditions detected:
  1. At vehicle speed of 3 km/h (2 mph) or more, IG1 terminal voltage 9.5 V or less for 10 seconds or more.
  2. When solenoid relay remains ON and IG1 terminal voltage 9.5 V or less, relay contact open for 0.2 seconds or more.
  3. When IG1 terminal voltage 9.5 V or less, vehicle speed sensor power supply decreases for 60 seconds or more.
  1. Battery
  2. Charging system
  3. Power source circuit
  4. Internal power supply circuit of skid control ECU

WIRING DIAGRAM

C120364E02
C117855E03

INSPECTION PROCEDURE


1. CHECK SKID CONTROL ECU TERMINAL VOLTAGE

  1. C121700E02
    Disconnect the skid control ECU connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Specified Condition
    A31-46 (IG1) - Body ground
    11 to 14 V



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Drive the vehicle at 3 km/h (2 mph) or more for several seconds.

  1. Check if the same DTC is output (Click here).

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE ABS AND TRACTION ACTUATOR

3. INSPECT FUSES (ECU-IG, AM1)

  1. C118694E01
    Remove the ECU-IG and AM1 fuses from the main body ECU.

  1. Measure the resistance.

    Standard Resistance:
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


4. INSPECT BATTERY
  1. Check the battery voltage.

    Standard Voltage:
    11 to 14 V



NG
CHECK CHARGING SYSTEM
OK


5. INSPECT IGNITION RELAY NO. 1

  1. C118689E01
    Remove the IG1 relay from the main body ECU.

  1. C113445
    Measure the resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Always
    10 kΩ or higher
    3 - 5
    Apply B+ between terminals 1 and 2
    Below 1 Ω



NG
REPLACE IGNITION RELAY NO. 1
OK


6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BODY GROUND)

  1. C121700E03
    Inspect the skid control ECU connector fitting for defects.

  1. Disconnect the skid control ECU connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    A31-32 (GND1) - Body ground
    Below 1 Ω
    A31-1 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ABS AND TRACTION ACTUATOR


← C1232/32 Stuck in Deceleration Sensor (+ 7 more codes) (from Aug 2005)C1246/46 Master Cylinder Pressure Sensor Malfunction (+ C1281/81) (from Aug 2005) →