2005-2008 Yaris · Service Manual ENGINE

P0141 Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

In order to obtain a high purification rate for the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a Three-Way Catalytic Converter (TWC) is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel ratio. The heated oxygen sensor has the characteristic whereby its output voltage changes suddenly in the vicinity of the stoichiometric air-fuel ratio. This is used to detect the oxygen concentration in the exhaust gas and provide the ECM with feedback to control the air-fuel ratio. When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas increases. The heated oxygen sensor informs the ECM of the lean condition (low voltage, i.e. less than 0.45 V). When the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas is reduced. And the heated oxygen sensor informs the ECM of the rich condition (high voltage, i.e. more than 0.45 V). The ECM judges, using the voltage output of the heated oxygen sensor, whether the air-fuel ratio is rich or lean and controls the injection time accordingly. If a malfunction of the heated oxygen sensor causes an output of abnormal voltage, the ECM is unable to perform accurate air-fuel ratio control. The heated oxygen sensor includes a heater which heats the zirconia element. The heater is controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is low), a current flows to the heater in order to heat the sensor for accurate oxygen concentration detection.
G035432E07

HINT:
The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.

A116151E04
DTC No.
DTC Detection Condition
Trouble Area
P0141
Open or short of heated oxygen sensor (sensor 2) heater or related circuit
(3 trip detection logic)
  1. Open or short in heated oxygen sensor (sensor 2) heater circuit
  2. Heated oxygen sensor heater (sensor 2)
  3. EFI relay
  4. ECM

HINT:
  1. DTC P0141 is detected when the engine idles for 1 minute.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
  3. Sensor 2 refers to the sensor mounted behind the TWC and located far from the engine assembly.


WIRING DIAGRAM

A109127E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT HEATED OXYGEN SENSOR (SENSOR RESISTANCE)
A120335E01
  1. Disconnect the heated oxygen sensor (sensor 2) connector.

  1. Measure the resistance between the terminals of the heated oxygen sensor connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    HT1B (1) - +B (2)
    6 to 14 Ω at 25°C (77°F)
    HT1B (1) - E1 (4)
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR (SENSOR 2)
OK


2. CHECK TERMINAL VOLTAGE (+B TERMINAL OF HEATED OXYGEN SENSOR)
A120347E01
  1. Disconnect the heated oxygen sensor (sensor 2) connector.

  1. Measure the voltage between the terminal of the heated oxygen sensor connector and the body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (C35-2) - Body ground
    9 to 14 V

  1. Reconnect the heated oxygen sensor.



OK
Go to step 4
NG


3. INSPECT INTEGRATION RELAY (EFI RELAY)
A107921E08
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the EFI fuse.

    1. Remove the EFI fuse.

    2. Check the fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the fuse.

  1. Inspect relay.

    1. Check the relay resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      1C-1 - 1A-8
      10 kΩ or higher
      1C-1 - 1A-8
      Below 1 Ω
      (When battery voltage applied to terminals 1C-1 and 1A-7)

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION RELAY
OK


4. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - HEATED OXYGEN SENSOR - ECM)
A120339E01
  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the heated oxygen sensor (sensor 2) connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    HT1B (C35-1) - HT1B (C33-62)
    Below 1 Ω
    +B (C35-2) - Engine room R/B (1A-8)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    HT1B (C35-1) or HT1B (C33-62) - Body ground
    10 kΩ or higher
    +B (C35-2) or Engine room R/B (1A-8) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the heated oxygen sensor connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK WHETHER DTC OUTPUT RECURS (DTC P0141)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Clear the DTCs.

  1. Start the engine.

  1. Allow the engine to idle for 1minute or more.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Pending.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    No DTC output
    A
    P0141
    B



B
REPLACE ECM
A

GO TO CHECK FOR INTERMITTENT PROBLEMS


← P0139 Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2) (from Aug 2005)P0171 System Too Lean (Bank 1) (+ P0172) (from Aug 2005) →