2005-2008 Yaris · Service Manual ENGINE

P0171 System Too Lean (Bank 1)

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

The fuel trim relates to the feedback compensation value, not to the basic injection time. The fuel trim includes the short-term fuel trim and the long-term fuel trim.
The short-term fuel trim is the short-term fuel compensation used to maintain the air-fuel ratio at its ideal theoretical value. The signal from the heated oxygen sensor indicates whether the air-fuel ratio is rich or lean compared to the ideal theoretical value, triggering a reduction in the fuel volume if the air-fuel ratio is rich, and an increase in the fuel volume if it is lean.
The long-term fuel trim is the overall fuel compensation in order to balance the short-term fuel trim for a continual deviation from the central value due to individual engine differences, changes in the usage environment, and age deterioration.
If both the short-term fuel trim and the long-term fuel trim are lean or rich beyond the standard level, it is detected as a malfunction in the SFI system. The ECM illuminates the MIL and sets a DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0171
When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on lean side (3 trip detection logic)
  1. Injector blockage
  2. Manifold absolute pressure sensor
  3. Engine coolant temperature sensor
  4. Fuel pressure
  5. Gas leakage from exhaust system
  6. Open or short in heated oxygen sensor (sensor 1) circuit
  7. Heated oxygen sensor (sensor 1)
  8. ECM
P0172
When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on rich side (3 trip detection logic)
  1. Injector blockage
  2. Manifold absolute pressure sensor
  3. Engine coolant temperature sensor
  4. Fuel pressure
  5. Gas leakage from exhaust system
  6. Open or short in heated oxygen sensor (sensor 1) circuit
  7. Heated oxygen sensor (sensor 1)
  8. ECM

CAUTION:
Strictly observe traffic laws when performing the confirmation driving pattern.

HINT:
  1. These DTCs are detected when the vehicle is driven for approximately 20 minutes at a constant vehicle speed of between 80 km/h (50 mph) and 110 km/h (70 mph) with the transmission gear selector lever in the 5th position (a malfunction is detected if the learning value of the driving range deviates by 25 %).
  2. When DTC P0171 is set, the actual air-fuel ratio is lean. When DTC P0172 is set, the actual air-fuel ratio is rich.
  3. If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 may be set. The MIL then illuminates.
  4. If the total of the short-term fuel trim value and long-term fuel trim value is within 20 %, the system functions normally.
  5. When the air-fuel learning value is 1.23 or more, DTC P0171 is set.
  6. When the air-fuel learning value is 0.77 or less, DTC P017 is set.


WIRING DIAGRAM

A109127E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P0171 AND P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0171 or P0172
    A
    P0171 or P0172 and other DTCs
    B

    HINT:
    If any DTCs other than P0171 or P0172 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (Control the Injection Volume for A/F Sensor)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the intelligent tester ON.

  1. Warm up the engine.

  1. Run the engine at 2,500 rpm for approximately 3 minutes.

  1. On the intelligent tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor (A/F Control).

  1. Perform the A/F control operation with the engine in an idling condition (press the right or left button to change the fuel injection volume).

  1. Monitor the voltage output of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.

    Result:
    The heated oxygen sensor reacts in accordance with increases and decreases of the fuel injection volume:
    +25 % = Rich output:
    More than 0.5 V
    -12.5 % = Lean output:
    Less than 0.4 V

    NOTICE:
    1. Sensor 1 (front sensor) has an output delay of a few seconds.
    2. Sensor 2 (rear sensor) has a maximum output delay of approximately 20 seconds.


    Output voltage of heated oxygen sensor (sensor 1: front sensor)
    Output voltage of heated oxygen sensor (sensor 2: rear sensor)
    Mainly suspected trouble area
    Case 1
    Injection volume
    +25 %
    -12.5 %
    A103184
    Injection volume
    +25 %
    -12.5 %
    A103184
    -
    Output voltage
    More than 0.5 V
    Less than 0.4 V
    A104056
    Output voltage
    More than 0.5 V
    Less than 0.4 V
    A104057
    Case 2
    Injection volume
    +25 %
    -12.5 %
    A103184
    Injection volume
    +25 %
    -12.5 %
    A103184
    1. Heated oxygen sensor
    Output voltage
    Almost no reaction
    A103185
    Output voltage
    More than 0.5 V
    Less than 0.4 V
    A104057
    Case 3
    Injection volume
    +25 %
    -12.5 %
    A103184
    Injection volume
    +25 %
    -12.5 %
    A103184
    1. Extremely rich or lean actual air-fuel ratio
    2. Injector leakage or blockage
    3. Gas leakage from exhaust system
    4. Ignition system
    5. Fuel pressure
    6. Manifold absolute pressure sensor
    7. Engine coolant temperature sensor
    Output voltage
    Almost no reaction
    A103185
    Output voltage
    Almost no reaction
    A103185
    The following procedure enables the technician to check and graph the voltage outputs of both the heated oxygen sensors.To display the graph, select the following menu items on the tester: View / Line Graph.

    HINT:
    If the vehicle is short of fuel, the air-fuel ratio becomes lean and the heated oxygen sensor DTCs are recorded, and then the MIL illuminates.


    Result:
    Result
    Proceed To
    Case 1
    C
    Case 2
    B
    Case 3
    A



B
Go to step 9

C
Go to step 11
A


3. READ VALUE OF ENGINE COOLANT TEMPERATURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp value when the engine is cold and warmed up.

    Standard:
    When the engine is cold:
    Same as the ambient temperature
    When the engine is warmed up:
    75 to 95°C (167 to 203°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


4. READ VALUE OF MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / MAP and Coolant Temp.

  1. Allow the engine to idle until the Coolant Temp reaches 75°C (167°F).

  1. Read the MAP value at idling and 2,500 rpm.

    Standard:
    Engine condition
    Tester Display
    Ignition switch on (IG)
    (Engine not running)
    50 to 115 kPa
    Idling
    (Shift position in N and A/C OFF)
    17 to 39 kPa
    2,500 rpm
    (Shift position in N and A/C OFF)
    22 to 50 kPa



NG
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
OK


5. CHECK SPARK AND IGNITION
  1. Check the spark (Click here).

    OK:
    Sparks occur.



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


6. CHECK FOR EXHAUST GAS LEAKAGE
  1. Check for exhaust gas leakage.

    OK:
    No gas leakage.



NG
REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT
OK


7. CHECK FUEL PRESSURE
  1. Check fuel pressure (Click here).

    Standard:
    304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44.1 to 49.7 psi)



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8. INSPECT FUEL INJECTOR
  1. Check the injector volume (Click here).

    Standard:
    47 to 58 mm3 (2.87 to 3.54 cu in.) in 15 seconds



NG
REPLACE FUEL INJECTOR
OK


9. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
A120336E01
  1. Disconnect the heated oxygen sensor (sensor 1) connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    OX1A (C36-3) - OX1A (C33-18)
    Below 1 Ω
    HT1A (C36-1) - HT1A (C33-41)
    Below 1 Ω
    E1 (C36-4) - E11 (C33-17)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    OX1A (C36-3) or OX1A (C33-18) - Body ground
    10 kΩ or higher
    HT1A (C36-1) or HT1A (C33-41) - Body ground
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor (sensor 1) connector.

  1. Reconnect the ECM connector.A116151E01



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. REPLACE HEATED OXYGEN SENSOR (SENSOR 1)

NEXT


11. PERFORM CONFIRMATION DRIVING PATTERN
  1. Clear the DTCs.

  1. Drive the vehicle for approximately 20 minutes at a vehicle speed between 80 km/h and 110 km/h (between 50 mph and 70 mph) with the transmission gear selector lever in the 5th position.


NEXT


12. CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Pending.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    No DTC output
    A
    P0171 or P0172
    B



B
Go to step 3
A

END


← P0141 Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2) (from Aug 2005)P0261 Cylinder 1 Injector Circuit Low (+ 5 more codes) (from Aug 2005) →