2005-2008 Yaris · Service Manual ENGINE

P0117 Engine Coolant Temperature Circuit Low Input

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

A thermistor is built into the engine coolant temperature sensor and changes its resistance value according to the engine coolant temperature. The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.

HINT:
  1. When the engine coolant temperature sensor output is outside the normal range, the ECM interprets this as a malfunction.
  2. If DTC P0117 or P0118 is detected, the ECM performs engine control using an estimated engine coolant temperature calculated from the intake air temperature at the time of engine start and the intake air volume.

DTC No.
DTC Detection Condition
Trouble Area
P0117
Engine coolant temperature sensor output is less than -47°C (-53°F) for 0.5 seconds when ignition switch is on (IG) or engine is running (3 trip detection logic)
  1. Open or short in engine coolant temperature sensor circuit
  2. Short to power source circuit
  3. Engine coolant temperature sensor
  4. ECM
P0118
Engine coolant temperature sensor output is more than 143°C (289°F) for 0.5 seconds when ignition switch is on (IG) or engine is running (3 trip detection logic)
  1. Short in engine coolant temperature sensor circuit
  2. Engine coolant temperature sensor
  3. ECM

HINT:
When DTC P0117 or P0118 is detected, check the engine coolant temperature by selecting Powertrain / Engine and ECT / Data List / Coolant Temp on the intelligent tester.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open or short to +B circuit
140°C (284°F)
Short to GND

WIRING DIAGRAM

A109125E02

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE OF ENGINE COOLANT TEMPERATURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    Standard:
    75 to 97°C (167 to 207°F) after warming up the engine.


    Result:
    Temperature Displayed
    Proceed To
    -40°C (-40°F)
    A
    140°C (284°F)
    B
    Same as actual engine coolant temperature
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    2. If there is a short to GND, the intelligent tester indicates 140°C (284°F).



B
Go to step 4

C
GO TO CHECK FOR INTERMITTENT PROBLEMS
A


2. CHECK WIRE HARNESS (CHECK FOR OPEN IN WIRE HARNESS)
A104053E02
  1. Confirm that the engine coolant temperature sensor connector is connected properly.

  1. Disconnect the engine coolant temperature sensor connector.

  1. Connect terminals THW and E2 of the engine coolant temperature sensor wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    Standard:
    140°C (284°F)

  1. Reconnect the engine coolant temperature sensor connector.



OK
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
NG


3. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
A116147E02
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    THW (C19-2) - THW (C33-56)
    Below 1 Ω
    E2 (C19-1) - E2 (C33-36)
    Below 1 Ω

  1. Reconnect the engine coolant temperature sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

4. CHECK WIRE HARNESS (CHECK FOR SHORT IN WIRE HARNESS)
A084869E33
  1. Disconnect the engine coolant temperature sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    Standard:
    -40°C (-40°F)

  1. Reconnect the engine coolant temperature sensor connector.



OK
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
NG


5. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
A116147E01
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    THW (C19-2) or THW (C33-56) - Body ground
    10 kΩ or higher

  1. Reconnect the engine coolant temperature sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0112 Intake Air Temperature Circuit Low Input (+ P0113) (from Aug 2005)P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem (+ P0221) (from Aug 2005) →