2005-2008 Yaris · Service Manual ENGINE

P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, Camshaft Timing Oil Control Valve (OCV) and VVT controller. The ECM sends a target "duty-cycle" control signal to the OCV. This control signal, applied to the OCV, regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed based on engine operating conditions such as intake air volume, throttle position and engine coolant temperature. The ECM controls the OCV based on the signals from several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, engine torque and fuel economy improve, and the exhaust emissions drop. The ECM detects actual valve timing using signals from the camshaft and crankshaft position sensors. The ECM performs feedback control and verifies target valve timing.
A093868E01
DTC No.
DTC Detection Condition
Trouble Area
P0011
Difference between the target camshaft angle and the actual camshaft angle is more then 10° after foreign object removal activation operated (1 or 2 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve (OCV)
  3. VVT controller assembly
  4. ECM
P0011
Relative angle of the camshaft and crankshaft deviates by 10° CA (crankshaft angle) from the standard angle at the advanced VVT side
(3 trip detection logic)
  1. Valve timing (jumped teeth of timing chain, chain stretched)
  2. Camshaft timing oil control valve (OCV)
  3. VVT controller assembly
  4. ECM
P0012
Relative angle of the camshaft and crankshaft deviates by 15° CA from the standard angle at the retarded VVT side
(3 trip detection logic)

HINT:
  1. DTC P0011 is detected when the vehicle is driven in the city for approximately 20 minutes after warm- up (repetitive acceleration for 3 seconds and deceleration for 5 seconds).
  2. DTC P0012 is detected when the engine idles for approximately 10 seconds after warm-up. If not detected, rev up the engine and let it idle for approximately 10 seconds again.


WIRING DIAGRAM

A109123E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).


1. CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO P0011 OR P0012)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0011 or P0012
    A
    P0011 or P0012, and other DTCs
    B

    HINT:
    If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OCV OPERATION)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank1).

  1. Check the engine speed when operating the Camshaft Timing Oil Control Valve (OCV) using the intelligent tester.


Result:
Specified Condition
Proceed To
Engine changes from steady idling to rough idling or engine stalling
A
No change in engine speed
B



B
Go to step 5
A


3. CHECK VALVE TIMING
  1. Check for looseness or a jumped tooth in the timing chain.

    OK:
    The match marks of the crankshaft pulley and camshaft pulley align.



NG
ADJUST VALVE TIMING
OK


4. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
  1. Clear the DTC using the intelligent tester.

  1. Start the engine and warm it up.

  1. Drive the vehicle for 20 minutes or more.

  1. Connect the intelligent tester to the DLC3.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Pending.

  1. Read DTCs.

    OK:
    No DTC output.

    HINT:
    DTC P0011 or P0012 may be set when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain set even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.



OK
VVT SYSTEM OK
NG


5. INSPECT ECM (OCV SIGNAL)

  1. A120345E01
    Disconnect the OCV connector.

  1. While running the engine at idle, check the waveform between the terminals of the OCV connector using the oscilloscope.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    Correct waveform is as shown

  1. Reconnect the OCV connector.



NG
Go to step 12
OK


6. INSPECT OIL CONTROL VALVE FILTER
A104040
  1. Remove the oil control valve filter.

  1. Check the oil control valve.

    OK:
    The filter is not clogged.

  1. Reinstall the oil control valve filter.



NG
REPLACE OIL CONTROL VALVE FILTER
OK


7. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE
A097066E02
  1. Remove the camshaft timing oil control valve.

  1. Apply the battery voltage to the camshaft timing oil control valve terminals.

  1. Check the valve operation.

    OK:
    The valve has no contamination and moves smoothly.

  1. Reinstall the camshaft timing oil control valve.



OK
Go to step 9
NG


8. REPLACE CAMSHAFT TIMING OIL CONTROL VALVE

NEXT


9. INSPECT CAMSHAFT TIMING SPROCKET ASSEMBLY
  1. Inspect the camshaft timing sprocket assembly.

    OK:
    The camshaft timing gear rotates smoothly when pressure is applied.



OK
Go to step 11
NG


10. REPLACE CAMSHAFT TIMING SPROCKET ASSEMBLY

NEXT


11. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
  1. Clear the DTC using the intelligent tester.

  1. Start the engine and warm it up.

  1. Drive the vehicle for 20 minutes or more.

  1. Connect the intelligent tester to the DLC3.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Pending.

  1. Read DTCs.

    OK:
    No DTC output.

    HINT:
    DTC P0011 or P0012 may be set when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain set even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.



OK
VVT SYSTEM OK
NG

GO TO CHECK FOR INTERMITTENT PROBLEMS

12. CHECK HARNESS AND CONNECTOR (OCV - ECM)
A116142E01
  1. Disconnect the OCV connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    OCV- (C24-2) - OCV- (C33-61)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    OCV- (C24-2) - Body ground
    10 kΩ or higher

  1. Reconnect the OCV connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0010 Camshaft Position "A" Actuator Circuit (Bank 1) (from Aug 2005)P0106 Manifold Absolute Pressure / Barometric Pressure Circuit Range / Performance Problem (from Aug 2005) →