2005-2008 Yaris · Service Manual ENGINE

P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

By a built-in sensor unit, the manifold absolute pressure sensor detects the intake manifold pressure as a voltage. The ECM then determines the basic injection duration and basic ignition advance angle based on this voltage.
P001242E01
DTC No.
DTC Detecting Condition
Trouble Area
P0107
The output voltage from the vacuum sensor remains 0.1 V or less for 2 seconds or more. (1 trip detection logic)
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. ECM
P0108
The output voltage from the vacuum sensor remains 4.9 V or more for 2 seconds or more. (1 trip detection logic)
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. ECM

HINT:
  1. DTC P0107 and P0108 are detected when the ignition switch is on (IG) position for approximately 10 seconds.
  2. When DTC P0107 or P0108 is detected, check the manifold absolute pressure by selecting Powertrain / Engine and ECT / Data List / MAP on the intelligent tester.

Manifold Absolute Pressure (kPa)
Malfunction
Approximately 0
  1. PIM circuit short
130 or more
  1. VC circuit open or short
  2. PIM circuit open
  3. E2 circuit open
  4. ECM

WIRING DIAGRAM

A109124E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE OF MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Turn the intelligent tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / MAP.

  1. Read the MAP value.

    Standard:
    Ignition switch on (IG):
    50 to 115 kPa



OK
GO TO CHECK FOR INTERMITTENT PROBLEMS
NG


2. CHECK TERMINAL VOLTAGE (MANIFOLD ABSOLUTE PRESSURE SENSOR)
A104038E02
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of the manifold absolute pressure sensor connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    2 - 3
    4.5 to 5.5 V

  1. Reconnect the manifold absolute pressure sensor connector.



OK
Go to step 4
NG


3. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
A116146E01
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VC (C34-3) - VC2 (C33-40)
    Below 1 Ω
    E2 (C34-2) - E21 (C33-35)
    Below 1 Ω
    PIM (C34-1) - PIM (C33-20)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VC2 (C33-40) - Body ground
    10 kΩ or higher
    PIM (C33-20) - Body ground
    10 kΩ or higher

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

4. REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (P0107 OR P0108)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Clear the DTC and turn the ignition switch off.

  1. Turn the ignition switch on (IG) and wait for 10 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    OK:
    No DTC output.



OK
END
NG

REPLACE ECM


← P0106 Manifold Absolute Pressure / Barometric Pressure Circuit Range / Performance Problem (from Aug 2005)P0112 Intake Air Temperature Circuit Low Input (+ P0113) (from Aug 2005) →