2005-2008 Yaris · Service Manual ENGINE

P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built from Nov 2006

Also covers:

DESCRIPTION

  1. Refer to DTC P0136 (Click here).

HINT:
  1. Sensor 2 refers to the sensor mounted behind the three way catalytic converter and located far from the engine assembly.
  2. When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

  3. The ECM provides a pulse width modulated signal to the control circuit to adjust the current through the heater. The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.

    A159683E01
DTC No.
DTC Detection Condition
Trouble Area
P0037
Heated oxygen sensor heater current less than 0.3 A
(1 trip detection logic)
  1. Open in heated oxygen sensor heater circuit
  2. Heated oxygen sensor (sensor 2)
  3. Integration relay (EFI relay)
  4. ECM
P0038
Heated oxygen sensor heater current more than 2 A
(1 trip detection logic)
  1. Short in heated oxygen sensor heater circuit
  2. Heated oxygen sensor (sensor 2)
  3. Integration relay (EFI relay)
  4. ECM


WIRING DIAGRAM

Refer to DTC P0136 (Click here).

CONFIRMATION DRIVING PATTERN

These DTCs are detected when the engine idles for 110 seconds or more.

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

  1. A115661E24
    Disconnect the heated oxygen sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HT1B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT1B) - 4 (E2)
    Always
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR
OK


2. CHECK TERMINAL VOLTAGE (POWER SOURCE)

  1. A072895E18
    Disconnect the heated oxygen sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D28-2 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V

  1. Reconnect the heated oxygen sensor connector.



NG
Go to step 4
OK


3. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

  1. A104950E31
    Disconnect the heated oxygen sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D28-1 (HT1B) - C20-47 (HT1B)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D28-1 (HT1B) or C20-47 (HT1B) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

4. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - INTEGRATION RELAY)

  1. A112604E02
    Disconnect the heated oxygen sensor connector.

  1. Remove the integration relay (EFI relay) from the engine room R/B and J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D28-2 (+B) - 1A-4
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D28-2 (+B) or 1A-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT (Click here)


← P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) (+ P0032) (from Nov 2006)P0100 Mass or Volume Air Flow Circuit (+ P0102, P0103) (from Nov 2006) →