2005-2008 Yaris · Service Manual ENGINE

P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)

Diagnostic trouble codes · Vehicles built from Nov 2006

Also covers:

DESCRIPTION

HINT:
Sensor 2 refers to the sensor mounted behind the three way catalytic converter and located far from the engine assembly.

A three way catalyst converter is used in order to convert the carbon monoxide, hydrocarbons, and nitrogen oxide, into less harmful substances. To allow the three way catalytic converter to function effectively, it is necessary to keep the air fuel ratio of the engine near the stoichiometric air fuel ratio. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.
The heated oxygen sensor is located behind the three way catalytic converter, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The heated oxygen sensor informs the ECM that the post-three way catalytic converter air fuel ratio is lean (low voltage, i.e. less than 0.45 V).
Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas becomes lean. The heated oxygen sensor informs the ECM that the post-three way catalytic converter air fuel ratio is rich (high voltage, i.e. more than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the three way catalytic converter is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.
A088111E19
DTC No.
DTC Detection Condition
Trouble Area
P0136
  1. Abnormal voltage output:
    During active air fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic):
    1. (a) Heated oxygen sensor voltage not decrease to less than 0.21 V
    1. (b) Heated oxygen sensor voltage not increase to more than 0.59 V
  1. Open or short in heated oxygen sensor (sensor 2) circuit
  2. Heated oxygen sensor (sensor 2)
  3. Air fuel ratio sensor (sensor 1)
  4. Gas leak from exhaust system
P0137
  1. Low voltage (open):
    During active air fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic):
    1. (a) Heated oxygen sensor voltage output less than 0.21 V
    1. (b) Target air fuel ratio rich
  1. Open in heated oxygen sensor (sensor 2) circuit
  2. Heated oxygen sensor (sensor 2)
  3. Gas leak from exhaust system
P0138
  1. High voltage (short):
    During active air fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic):
    1. (a) Heated oxygen sensor voltage output 0.59 V or more
    1. (b) Target air fuel ratio lean
  1. Short in heated oxygen sensor (sensor 2) circuit
  2. Heated oxygen sensor (sensor 2)
  3. Air fuel ratio sensor (sensor 1)
  4. ECM

WIRING DIAGRAM

A159159E01

CONFIRMATION DRIVING PATTERN

HINT:
  1. This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.
  2. Performing this confirmation pattern will activate the heated oxygen sensor monitor. (The catalyst monitor is performed simultaneously.) This is very useful for verifying the completion of the repair.

A115372E98
  1. Connect an intelligent tester to the DLC3.
  2. Turn the ignition switch on (IG).
  3. Turn the tester on.
  4. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.
  5. Clear DTCs.
  6. Switch the ECM from normal mode to check mode (Click here).
  7. Select the following menu items: Powertrain / Engine and ECT / Data List / O2S (A/FS) Monitor.
  8. Check that the item O2S (A/FS) Monitor displays Incmpl (Incomplete).
  9. Start the engine and warm it up. (Proceed to "A")
  10. Drive the vehicle at between 90 km/h and 110 km/h (56 mph and 68 mph) for at least 10 minutes. (Proceed to "B")
  11. Note the state of the Data List items. Those items will change to Compl (Complete) as the O2 Sensor monitor operates.
  12. On the tester, select the following menu items: Powertrain / Engine and ECT / DTC and check if any DTCs (any pending DTCs) are set.

HINT:
If the item O2S (A/FS) Monitor does not change to Compl (Complete), and any pending DTCs fail to set, extend the driving time.


INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. On the tester, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1 S1
(A/F)
+25%
Rich
Less than 3.0 V
AFS B1 S1
(A/F)
-12.5%
Lean
More than 3.35 V
O2S B1 S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1 S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E01
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E01
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Fuel injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2.

HINT:
  1. Read freeze frame data using an intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ OUTPUT DTC (DTC P0136, P0137 OR P0138)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P0138
    A
    P0137
    B
    P0136
    C



B
Go to step 13

C
Go to step 6
A


2. READ VALUE OF INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2.

  1. Allow the engine to idle.

  1. Read the heated oxygen sensor output voltage while idling.

    Result:
    Result
    Proceed to
    More than 1.2 V
    A
    Less than 1.0 V
    B



B
Go to step 5
A


3. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

  1. A152957E06
    Turn the ignition switch off and wait for 5 minutes.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    C20-47 (HT1B) - C20-64 (OX1B)
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.



NG
Go to step 4
OK

REPLACE ECM

4. INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

  1. A115661E26
    Disconnect the heated oxygen sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HT1B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    2 (+B) - 3 (OX1B)
    Always
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - HEATED OXYGEN SENSOR)

5. INSPECT AIR FUEL RATIO SENSOR

HINT:
This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will indicate below 3 mA in this test.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs.

  1. Drive the vehicle by the drive pattern as listed below:

    1. Warm up the engine.

    2. Drive the vehicle at 60 km/h (40 mph) or more for 10 minutes or more.

    3. Stop the vehicle.

    4. Accelerate the vehicle up to 60 km/h (40 mph) or more and then decelerate for 3 seconds or more. Repeat this process at least 3 times.A152792E02

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / A/F Control System / AFS B1 S1.

  1. Read the value of the air fuel ratio sensor current while the fuel-cut operation is performing.

    Standard current:
    Less than 3.0 mA

    HINT:
    1. To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.
    2. If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the intelligent tester.

Result:
Result
Proceed to
Outside standard range
A
Within standard range
B



B
Go to step 9
A

REPLACE AIR FUEL RATIO SENSOR

6. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1 S2.

  1. After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.

  1. Read the output voltage of the heated oxygen sensor when the engine rpm is suddenly increased.

    HINT:
    Quickly accelerate the engine to 4000 rpm 3 times using the accelerator pedal.

    Standard voltage:
    Fluctuates between 0.4 V or less and 0.55 V or more.



NG
Go to step 13
OK


7. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Pending.

    Result:
    Result
    Proceed to
    P0136
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


9. REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).


NEXT


10. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


11. CHECK WHETHER DTC OUTPUT RECURS (DTC P0136)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Pending.

    Result:
    Result
    Proceed to
    P0136
    A
    No output
    B



B
REPAIR COMPLETED
A


12. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine.

  1. Select the following menu items: Powertrain / Engine / Active Test / Control the Injection Volume.

  1. Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.

    HINT:
    1. Change the fuel injection volume within the range of -12% and +12%. The injection volume can be changed in 1% graduations within this range.
    2. The air fuel ratio sensor is displayed as AFS B1 S1, and the heated oxygen sensor is displayed as O2S B1 S2 on the intelligent tester.


    Result:
    Tester Display (Sensor)
    Voltage Variation
    Proceed to
    AFS B1 S1 (A/F)
    Alternates between more and less than 3.3 V
    OK
    AFS B1 S1 (A/F)
    Remains at more than 3.3 V
    NG
    AFS B1 S1 (A/F)
    Remains at less than 3.3 V
    NG

    HINT:
    A normal heated oxygen sensor voltage (O2S B1 S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either less or more than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.

    A121606E04



NG
REPLACE AIR FUEL RATIO SENSOR
OK

REPAIR OR REPLACE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (FUEL INJECTOR, FUEL PRESSURE, EXHAUST GAS LEAK, ETC.) (Click here)

13. INSPECT FOR EXHAUST GAS LEAK

OK:
No gas leak.



NG
REPAIR OR REPLACE EXHAUST GAS LEAK POINT
OK


14. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

  1. A115661E25
    Disconnect the heated oxygen sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HT1B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT1B) - 4 (E2)
    Always
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR
OK


15. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

  1. A104950E32
    Disconnect the heated oxygen sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    D28-1 (HT1B) - C20-47 (HT1B)
    Always
    Below 1 Ω
    D28-3 (OX1B) - C20-64 (OX1B)
    Always
    Below 1 Ω
    D28-4 (E2) - C20-87 (EX1B)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D28-1 (HT1B) or C20-47 (HT1B)) - Body ground
    Always
    10 kΩ or higher
    D28-3 (OX1B) or C20-64 (OX1B) - Body ground
    Always
    10 kΩ or higher
    D28-4 (E2) or C20-87 (EX1B) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor connector.

  1. Reconnect the ECM connector.A159683E01



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HEATED OXYGEN SENSOR


← P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem (from Nov 2006)P0171 System Too Lean (Bank 1) (+ P0172) (from Nov 2006) →