2005-2008 Yaris · Service Manual ENGINE

P0443 Evaporative Emission Control System Purge Control Valve Circuit

Diagnostic trouble codes · Vehicles built from Nov 2006

DESCRIPTION

To reduce hydrocarbon emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.
The ECM changes the duty signals to the Purge VSV (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.
DTC No.
DTC Detection Condition
Trouble Area
P0443
Terminal voltage of ECM output circuit does not correspond with drive signals from ECM to purge VSV
(1 trip detection logic)
  1. Open or short in purge VSV circuit
  2. Purge VSV
  3. ECM

WIRING DIAGRAM

A159162E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE PURGE VSV CONTROL)

  1. A159447E01
    Connect an intelligent tester to the DLC3.

  1. Disconnect the vacuum hose (charcoal canister side) from the purge VSV.

  1. Start the engine.

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

  1. When the purge VSV is operated using the intelligent tester, check whether the port of the purge VSV applies suction to your finger.

    OK:
    Tester Operation
    Specified Condition
    VSV ON
    Purge VSV port applies suction to finger
    VSV OFF
    Purge VSV port applies no suction to finger

  1. Reconnect the vacuum hose to the purge VSV.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT PURGE VSV (RESISTANCE)

  1. A152887E02
    Disconnect the purge VSV connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    23 to 26 Ω

  1. Reconnect the purge VSV connector.



NG
REPLACE PURGE VSV
OK


3. INSPECT PURGE VSV (POWER SOURCE)

  1. A107917E14
    Disconnect the purge VSV connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C3-2 - Body ground
    Ignition switch on (IG)
    11 to 14 V

  1. Reconnect the purge VSV connector.



NG
Go to step 5
OK


4. CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

  1. A107919E12
    Disconnect the purge VSV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C3-1 - C20-49 (PRG)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C3-1 or C20-49 (PRG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the purge VSV connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

5. CHECK HARNESS AND CONNECTOR (PURGE VSV - INTEGRATION RELAY)

  1. A159768E01
    Disconnect the purge VSV connector.

  1. Remove the integration relay (EFI relay) from the engine room R/B and J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C3-2 - 1A-4
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C3-2 or 1A-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the purge VSV connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT (Click here)


← P0420 Catalyst System Efficiency Below Threshold (Bank 1) (from Nov 2006)P0500 Vehicle Speed Sensor "A" (from Nov 2006) →