2005-2008 Yaris · Service Manual BRAKE

C0273/13 Open or Short Circuit in ABS Motor Relay Circuit

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

If a DTC related to the motor line is stored, the VSC2 relay cuts off the power supply to the VSC1 relay and performs the fail-safe operation.
While any of the ABS, TRC, VSC, or BA is operating, the skid control ECU turns the VSC2 relay on and activates the pump motor in the ABS and TRACTION actuator.
These DTCs may be stored if the motor relay (+BM) voltage becomes lower than the DTC detecting condition due to insufficient output from the battery or alternator.
DTC No.
DTC Detecting Conditions
Trouble Areas
C0273/13
When either of following conditions (1 or 2) detected:
  1. All of following conditions continue for 0.2 seconds or more.
    1. IG1 terminal voltage between 9.5 V and 17.2 V.
    2. During initial check or ABS operation.
    3. Relay contact open when relay on.
  2. Both of following conditions continue for 0.2 seconds or more.
    1. IG1 terminal voltage 9.5 V or less.
    2. Relay contact remains open when relay on.
  1. ABS1/VSC1 fuse
  2. VSC1 relay
  3. VSC1 relay circuit
  4. VSC2 relay
  5. VSC2 relay circuit
  6. ABS and TRACTION actuator
C0274/14
Despite motor relay (VSC1 relay) off, motor relay remains closed for 4 seconds or more.
  1. ABS1/VSC1 fuse
  2. VSC1 relay
  3. VSC1 relay circuit
  4. VSC2 relay
  5. VSC2 relay circuit
  6. ABS and TRACTION actuator
C1361/91
Immediately after ignition switch turned on (IG), motor fail-safe relay (VSC2 relay) contact closed for 4 seconds when motor fail-safe relay (VSC2 relay) off.
  1. ABS1/VSC1 fuse
  2. VSC1 relay
  3. VSC1 relay circuit
  4. VSC2 relay
  5. VSC2 relay circuit
  6. ABS and TRACTION actuator

HINT:
C0273/13, C0274/14 and C1361/91: The skid control ECU begins to detect these DTCs when the vehicle speed exceeds 6 km/h (4 mph).


WIRING DIAGRAM

C118706E02

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST BY INTELLIGENT TESTER

  1. A107926E08
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTC(s) (Click here).

  1. Perform the active test using the intelligent tester.Select the following menu items: Chassis / ABS/VSC/TRC / Active Test.

    ACTIVE TEST: ABS/VSC/TRC 
    Item (Display)
    Vehicle Condition / Test Details
    Diagnostic Note
    Motor Relay
    Turns ABS motor relay ON / OFF
    Operating sound of motor can be heard

  1. Check the operation sound of the ABS motor when operating it with the intelligent tester.

    OK:
    The operation sound of the ABS motor can be heard.



OK
Go to step 7
NG


2. INSPECT FUSE (ABS1/VSC1)

  1. C117863E05
    Remove the ABS1/VSC1 fuse from the engine room R/B.

  1. Measure the resistance.

    Standard Resistance:
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


3. INSPECT RELAY (VSC1)

  1. C121703E01
    Remove the VSC1 relay from the engine room R/B No. 7.

  1. F050240E02
    Measure the resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Always
    10 kΩ or higher
    3 - 5
    Apply B+ between terminal 1 and 2
    Below 1 Ω



NG
REPLACE RELAY
OK


4. INSPECT RELAY (VSC2)

  1. C121704E01
    Remove the VSC2 relay from the engine room R/B No. 7.

  1. F050241E04
    Measure the resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Always
    10 kΩ or higher
    3 - 5
    Apply B+ between terminal 1 and 2
    Below 1 Ω



NG
REPLACE RELAY
OK


5. CHECK NO. 7 ENGINE ROOM R/B

  1. C122521E01
    Remove the VSC1 relay and VSC2 relay from the engine room No. 7.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    VSC2 relay terminal 5 - Body ground
    Always
    11 to 14 V

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    VSC1 relay terminal 5 - VSC2 relay terminal 3
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM R/B NO. 7)
  1. Disconnect the skid control ECU connector.

  1. Remove the VSC1 relay and VSC2 relay from the engine room R/B No. 7.

  1. C122522E01
    Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    A31-2 (BM) - VSC1 relay terminal 3
    Below 1 Ω
    A31-14 (MRF) - VSC2 relay terminal 2
    Below 1 Ω
    A31-15 (MR) - VSC1 relay terminal 2
    Below 1 Ω
    A31-45 (R+) - VSC2 relay terminal 1
    Below 1 Ω
    A31-2 (BM) - Body ground
    10 kΩ or higher
    A31-14 (MRF) - Body ground
    10 kΩ or higher
    A31-15 (MR) - Body ground
    10 kΩ or higher
    A31-45 (R+) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at 6 km/h (4 mph) or more to activate the initial check.

  1. Check if the same DTC(s) is output (Click here).

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE ABS AND TRACTION ACTUATOR


← C0226/21 SFR Solenoid Circuit (+ C0236/22, C0246/23, C0256/24, C1225/25) (from Aug 2005)C0278/11 Open or Short Circuit in ABS Solenoid Relay Circuit (+ C0279/12) (from Aug 2005) →