2005-2008 Yaris · Service Manual BRAKE

C0278/11 Open or Short Circuit in ABS Solenoid Relay Circuit

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

The solenoid relay supplies power to the ABS solenoid and TRC solenoid.
After the ignition switch is turned on, the vehicle speed has reached 6 km/h (4 mph) and the solenoid is determined to be normal by the initial check self-diagnosis, the relay switches on. If any open or short circuits are detected, the relay switches off.
These DTCs may be set if the voltage supply to the solenoid relay (+BS) falls below the DTC detection threshold due to the battery or alternator outputs being insufficient.
DTC No.
DTC Detecting Conditions
Trouble Areas
C0278/11
When either of following conditions (1 or 2) detected:
  1. Both of following conditions continue for 0.2 seconds or more.
    1. IG1 terminal voltage between 9.5 V and 17.2 V.
    2. Solenoid relay contact open when relay on.
  2. Both of following conditions continue for 0.2 seconds or more.
    1. IG1 terminal voltage becomes lower than 9.5 V when relay turned on.
    2. Relay contact remains open.
  1. ABS2/VSC2 fuse
  2. Wire harness (+BS)
  3. ABS and TRACTION actuator
C0279/12
Immediately after ignition switch turned on, solenoid relay contact closed for 0.2 seconds or more when relay off.
  1. ABS2/VSC2 fuse
  2. Wire harness (+BS)
  3. ABS and TRACTION actuator

HINT:
C0278/11 and C0279/12: The skid control ECU begins to detect these DTCs when the vehicle speed exceeds 6 km/h (4 mph).


WIRING DIAGRAM

Click here.

INSPECTION PROCEDURE


1. INSPECT FUSE (ABS2/VSC2)

  1. C117851E04
    Remove the ABS2/VSC2 fuse from the engine room R/B.

  1. Measure the resistance.

    Standard Resistance:
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2. CHECK HARNESS AND CONNECTOR (BATTERY - SKID CONTROL ECU - BODY GROUND)

  1. C121700E01
    Inspect the skid control ECU connector fitting for any defects.

  1. Disconnect the skid control ECU connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Specified Condition
    A31-31 (+BS) - Body ground
    11 to 14 V

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    A31-32 (GND1) - Body ground
    Below 1 Ω
    A31-1 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at 6 km/h (4 mph) or more to activate the initial check.

  1. Check if the same DTCs are output (Click here).

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE ABS AND TRACTION ACTUATOR


← C0273/13 Open or Short Circuit in ABS Motor Relay Circuit (+ C0274/14, C1361/91) (from Aug 2005)C1201/51 Engine Control System Malfunction (from Aug 2005) →