2005-2008 Yaris · Service Manual ENGINE

P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1)

Diagnostic trouble codes · Vehicles built from Nov 2006

DESCRIPTION

HINT:
  1. This DTC relates to the Camshaft Timing Oil Control Valve (OCV) for exhaust camshaft.

The Variable Valve Timing (VVT) system includes the ECM, OCV and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV, based on the signals transmitted by several sensors. The VVT controller regulates the exhaust camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target valve timing is verified by the ECM.
A156445E03
DTC No.
DTC Detection Condition
Trouble Area
P0013
Open or short in Camshaft Timing Oil Control Valve (OCV) (for exhaust camshaft) circuit
(1 trip detection logic)
  1. Open or short in OCV (for exhaust camshaft) circuit
  2. OCV (for exhaust camshaft)
  3. ECM

WIRING DIAGRAM

A143411E06

INSPECTION PROCEDURE

HINT:
  1. If DTC P0013 is displayed, check the VVT system (for exhaust camshaft) circuit.
  2. Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK WHETHER DTC OUTPUT RECURS (DTC P0013)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs.

  1. Start the engine and warm it up.

  1. Allow the engine to idle 1 minute or more.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P0013
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

  1. A159178E02
    Remove the OCV (for exhaust camshaft).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

  1. A159174E01
    Apply battery voltage to terminals of the OCV (for exhaust camshaft). Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the OCV (for exhaust camshaft).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)
OK


3. CHECK HARNESS AND CONNECTOR (OCV FOR EXHAUST CAMSHAFT - ECM)

  1. A106380E29
    Disconnect the OCV (for exhaust camshaft) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C72-1 (OE1+) - C20-60 (OE1+)
    Always
    Below 1 Ω
    C72-2 (OE1-) - C20-61 (OE1-)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C72-1 (OE1+) or C20-60 (OE1+) - Body ground
    Always
    10 kΩ or higher
    C72-2 (OE1-) or C20-61 (OE1-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the OCV (for exhaust camshaft) connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012) (from Nov 2006)P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1) (+ P0015) (from Nov 2006) →