2005-2008 Yaris · Service Manual ENGINE

P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

Diagnostic trouble codes · Vehicles built from Nov 2006

Also covers:

DESCRIPTION

HINT:
  1. These DTCs relate to the Camshaft Timing Oil Control Valve (OCV) for intake camshaft. If DTC P0011 or P0012 is present, check the VVT (Variable Valve Timing) system.

The VVT system includes the ECM, OCV and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure applied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV, based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.
A156445E03
DTC No.
DTC Detection Condition
Trouble Area
P0011
Advanced camshaft timing:
With warm engine and engine speed of between 550 rpm and 4,000 rpm, all conditions (a), (b) and (c) met (1 trip detection logic):
(a) Difference between target and actual intake valve timings more than 5°CA (Crankshaft Angle) for 4.5 seconds
(b) Current intake valve timing fixed (timing changes less than 5°CA in 5 seconds)
(c) Variations in VVT controller timing more than certain angle of maximum delayed timing (malfunction in advance timing)
  1. Valve timing
  2. Camshaft Timing Oil Control Valve (OCV) (for intake camshaft)
  3. OCV filter
  4. Camshaft timing gear assembly (for intake camshaft)
  5. ECM
P0012
Retarded camshaft timing:
With warm engine and engine speed of between 550 rpm and 4,000 rpm, all conditions (a), (b) and (c) met (2 trip detection logic):
(a) Difference between target and actual intake valve timings more than 5°CA (Crankshaft Angle) for 4.5 seconds
(b) Current intake valve timing fixed (timing changes less than 5°CA in 5 seconds)
(c) Variations in VVT controller timing certain angle or less of maximum delayed timing (malfunction in retarded timing)
  1. Valve timing
  2. Camshaft Timing Oil Control Valve (OCV) (for intake camshaft)
  3. OCV filter
  4. Camshaft timing gear assembly (for intake camshaft)
  5. ECM

WIRING DIAGRAM

Refer to DTC P0010 (Click here).

INSPECTION PROCEDURE

NOTICE:
DTC P0011 or P0012 may be set when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain set even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.

HINT:
Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P0011 or P0012
    A
    P0011 or P0012 and other DTCs
    B

    HINT:
    If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV FOR INTAKE CAMSHAFT)
  1. Connect an intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).

  1. Check the engine speed while operating the OCV (for intake camshaft) using the tester.

    Result:
    Tester Operation
    Specified Condition
    OCV OFF
    Normal engine speed
    OCV ON
    Engine idles roughly or stalls
    (soon after OCV switched from OFF to ON)



NG
Go to step 4
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs.

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester.

  1. Drive the vehicle for more than 10 minutes.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    No output
    A
    P0011 or P0012
    B



B
Go to step 7
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

  1. A159178E01
    Remove the OCV (for intake camshaft).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

  1. A159175E01
    Apply battery voltage to terminals of the OCV (for intake camshaft). Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the OCV (for intake camshaft).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
OK


5. INSPECT OIL CONTROL VALVE FILTER

  1. A150883
    Remove the OCV filter.

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.

  1. Reinstall the OCV filter.



NG
CLEAN OIL CONTROL VALVE FILTER
OK


6. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (FOR INTAKE CAMSHAFT)
  1. Inspect the camshaft timing gear assembly (for intake camshaft) (Click here).



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (FOR INTAKE CAMSHAFT)
OK


7. ADJUST VALVE TIMING
A159445E01

HINT:
There are no marks on the cylinder head to match-up for the purpose of checking valve timing. Valve timing can only be inspected by lining up the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and re-install the chain to match up the timing marks (Click here).


NEXT


8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs.

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester.

  1. Drive the vehicle for more than 10 minutes.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    No output
    A
    P0011 or P0012
    B

    HINT:
    DTC P0011 or P0012 is output when foreign objects in engine oil are caught in some parts of the system. These codes will stay output for a short time even after the system returns to normal. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



B
REPLACE ECM
A

END


← P0010 Camshaft Position "A" Actuator Circuit (Bank 1) (from Nov 2006)P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1) (from Nov 2006) →