2005-2008 Yaris · Service Manual ENGINE

P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)

Diagnostic trouble codes · Vehicles built from Nov 2006

Also covers:

DESCRIPTION

HINT:
  1. These DTCs relate to the Camshaft Timing Oil Control Valve (OCV) for exhaust camshaft. If DTC P0014 or P0015 is present, check the VVT (Variable Valve Timing) system.

Refer to DTC P0013 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P0014
Advanced cam timing:
With warm engine and engine speed of between 500 rpm and 4,000 rpm, all conditions (a), (b) and (c) met
(2 trip detection logic):
(a) Difference between target and actual exhaust valve timing more than 5 °CA (Crankshaft Angle) for 4.5 seconds
(b) Current exhaust valve timing fixed (timing changes less than 5°CA in 5 seconds)
(c) Variations in VVT controller timing more than certain angle of maximum delayed timing (advanced)
  1. Valve timing
  2. Camshaft Timing Oil Control Valve (OCV) (for exhaust camshaft)
  3. OCV filter
  4. Camshaft timing gear assembly (for exhaust camshaft)
  5. ECM
P0015
Retarded cam timing:
With warm engine and engine speed of between 500 rpm and 4,000 rpm, all conditions (a), (b) and (c) met
(1 trip detection logic):
(a) Difference between target and actual exhaust valve timing more than 5°CA (Crankshaft Angle) for 4.5 seconds
(b) Current exhaust valve timing fixed (timing changes less than 5°CA in 5 seconds)
(c) Variations in VVT controller timing certain angle or less of maximum delayed timing (retarded)
  1. Valve timing
  2. Camshaft Timing Oil Control Valve (OCV) (for exhaust camshaft)
  3. OCV filter
  4. Camshaft timing gear assembly (for exhaust camshaft)
  5. ECM
If the difference between the target and actual exhaust valve timing is large, and changes in actual exhaust valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and sets a DTC.
Example:
A DTC is set when the following conditions 1), 2) and 3) are met:
1) The difference between the target and actual exhaust valve timing is more than 5°CA (Crankshaft Angle) and the condition continues for more than 4.5 seconds.
2) It takes 5 seconds or more to change the valve timing by 5°CA.
3) After above conditions 1) and 2) are met, the OCV is forcibly activated 63 times or more.
DTCs P0014 (Advanced Cam Timing) is subject to 2 trip detection logic.
DTCs P0015 (Retarded Cam Timing) is subject to 1 trip detection logic.
These DTCs indicate that the VVT controller cannot operate properly due to OCV malfunctions or the presence of foreign objects in the OCV.
The monitor will not run unless the following conditions are met:
  1. The engine is warm (the engine coolant temperature is 75°C [167°F] or more).
  2. The vehicle has been driven at more than 64 km/h (40 mph) for 3 minutes.
  3. The engine has idled for 3 minutes (retarded camshaft timing only).

WIRING DIAGRAM

Refer to DTC P0013 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014 OR P0015)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P0014 or P0015
    A
    P0014 or P0015 and other DTCs
    B

    HINT:
    If any DTCs other than P0014 or P0015 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST BY USING INTELLIGENT TESTER (OPERATE OCV)
  1. Connect an intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Warm up the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1).

  1. Check the engine speed while operating the OCV (for exhaust camshaft) using the tester.

    Result:
    Tester Operation
    Specified Condition
    -128% (OCV OFF)
    Normal engine speed
    127% (OCV ON)
    Engine idles roughly or stalls after OCV switched from OFF to ON



NG
Go to step 4
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0014 OR P0015)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs.

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester.

  1. Allow the engine to idle for 3 minutes or more.

  1. Drive the vehicle for more than 10 minutes.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    No output
    A
    P0014 or P0015
    B



B
Go to step 7
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

  1. A159178E02
    Remove the OCV (for exhaust camshaft).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

  1. A159174E01
    Apply battery voltage to terminals of the OCV (for exhaust camshaft). Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the OCV (for exhaust camshaft).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)
OK


5. INSPECT OIL CONTROL VALVE FILTER
A150883
  1. Remove the OCV filter.

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.

  1. Reinstall the OCV filter.



NG
CLEAN OIL CONTROL VALVE FILTER
OK


6. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (FOR EXHAUST CAMSHAFT)
  1. Inspect the camshaft timing gear assembly (for exhaust camshaft) (Click here).



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (FOR EXHAUST CAMSHAFT)
OK


7. ADJUST VALVE TIMING
A159445E01

HINT:
There are no marks on the cylinder head to match-up for the purpose of checking valve timing. Valve timing can only be inspected by lining up the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and re-install the chain to match up the timing marks (Click here).


NEXT


8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0014 OR P0015)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs.

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the tester.

  1. Allow the engine to idle for 3 minutes or more.

  1. Drive the vehicle for more than 10 minutes.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    No output
    A
    P0014 or P0015
    B

    HINT:
    DTC P0014 or P0015 is output when foreign objects in engine oil are caught in some parts of the system. These codes will stay output for a short time even after the system returns to normal. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



B
REPLACE ECM
A

END


← P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1) (from Nov 2006)P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) (+ P0017) (from Nov 2006) →