2005-2008 Yaris · Service Manual STEERING

B2782 Power Source Control ECU Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The steering lock ECU activates the steering lock motor by the power from the main body ECU through the IGE circuit. This prevents the steering from being locked while the vehicle is moving.
The diagnosis information of the steering lock ECU is transmitted to the tester via the certification ECU as the steering lock ECU is not connected to the CAN communication system.
DTC No.
Detection Item
Trouble Area
B2782
IGE power supply circuit malfunction
  1. Harness or connector
  2. Steering lock actuator assembly (Steering lock ECU)
  3. Main body ECU

WIRING DIAGRAM

C117908E01

INSPECTION PROCEDURE

HINT:
  1. Before starting the inspection by using the intelligent tester with the engine switch off, make sure that the driver door is open.
  2. When the engine switch is off, the main body ECU may not be working.
  3. Communication with the intelligent tester is impossible if the main body ECU is not working.


1. CHECK DTC (CERTIFICATION ECU)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Read the DTCs of the certification ECU by following the prompts displayed on the intelligent tester.

OK:
DTC B2785 that indicates malfunctions in LIN bus line, is not output.

HINT:
If DTC B2785 is output, inspect LIN communication system (Click here ).



NG
INSPECT COMMUNICATION SYSTEM (LIN)
OK


2. INSPECT STEERING LOCK ACTUATOR ASSEMBLY
C104383E01
  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    IGE (D56-3) - SGND (D56-2)
    Engine switch off
    10 to 14 V
    Turn engine switch from off to on (IG)
    Motor inactive:
    10 to 14 V
    ↓
    Motor active:
    Below 1 V
    ↓
    Motor inactive:
    10 to 14 V
    Engine switch on (IG)
    10 to 14 V
    IGE (D56-3) - SGND (D56-2)
    Adjust shift lever to P position
    ↓
    Turn engine switch off
    ↓
    Open driver door
    Motor inactive:
    10 to 14 V
    ↓
    Motor active:
    Below 1 V
    ↓
    Motor inactive:
    10 to 14 V

HINT:
The steering lock ECU and steering lock actuator assembly are supplied as a unit.



OK
REPLACE STEERING LOCK ACTUATOR ASSEMBLY
NG


3. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - BODY GROUND)

  1. C122327E01
    Disconnect the connector from the steering lock actuator assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    SGND (D56-2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - MAIN BODY ECU)

  1. C124982E01
    Disconnect the connector from the main body ECU.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IGE (D56-3) - SLR+ (D64-7)
    Always
    Below 1 Ω
    IGE (D56-3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← B2781 Open / Short in Steering Lock ECU (from Aug 2005)B2786 No Response from Steering Lock ECU (from Aug 2005) →