2005-2008 Yaris · Service Manual TRANSMISSION

PRECAUTION

Precautions · Vehicles built from Nov 2005


1.IGNITION SWITCH EXPRESSIONS
  1. The type of ignition switch used on this model differs according to the specifications of the vehicle. The expressions listed in the table below are used in this section.

    Expression
    Ignition Switch
    (position)
    Engine Switch
    (condition)
    Ignition Switch off
    LOCK
    Off
    Ignition Switch on (IG)
    ON
    On (IG)
    Ignition Switch on (ACC)
    ACC
    On (ACC)
    Engine Start
    START
    Start


2.PRECAUTION REGARDING ON-VEHICLE INSPECTION
  1. When racing the engine, make sure that the gear is in neutral.


3.PRECAUTION REGARDING PARTS REMOVAL AND INSTALLATION
  1. When removing or installing parts related to the multi-mode manual transmission system, perform [Clamp Position Adjustment], [Initialization and Learning] and/or [Synchronization Position Calibration]. In addition, the required operations differ according to the parts to be removed and installed. Proceed with the operation in the order shown in the table below.

    Before removal 
    Parts to be removed
    Operation order
    See procedure
    1. Clutch actuator
    2. Transmission assembly
    3. Transmission parts (inside gear box)
    4. Clutch disc and clutch cover
    5. Clutch release bearing
    6. Clutch release fork
    7. Flywheel
    8. Crankshaft
    1. CLAMP POSITION ADJUSTMENT
    Click here
    Before installation 
    Parts to be installed
    Operation order
    See procedure
    1. New clutch actuator
    1. CLAMP POSITION ADJUSTMENT
    Click here

    NOTICE:
    Pull rods of brand new clutch actuators (service supply parts) are not set to the clutch clamp position. Therefore, adjust the clamp positions before installing new clutch actuators.

    After installation 
    Parts installed
    Operation order
    See procedure
    1. Transmission assembly
    2. Transmission parts (inside gear box)
    3. Transmission control ECU
    1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
    [Initialization of ECU]
    Click here
    2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
    Click here
    3. SYNCHRONIZATION POSITION CALIBRATION
    Click here
    1. Shift and select actuator
    2. Shift stroke sensor
    3. Select stroke sensor
    1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
    [Initialization of transmission]
    Click here
    2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
    Click here
    3. SYNCHRONIZATION POSITION CALIBRATION
    Click here
    1. Clutch actuator
    2. Clutch stroke sensor
    3. Clutch disc and clutch cover
    4. Clutch release bearing
    5. Clutch release fork
    6. Flywheel
    7. Crankshaft
    1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
    [Initialization of clutch]
    Click here
    2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
    Click here

    NOTICE:
    1. Replace the clutch disc and clutch cover together. If only one is replaced, the adjustment system of the clutch cover does not function properly. This may cause clutch drag or clutch slippage, which may result in deterioration of drivability or malfunctions of the system parts.
    2. After replacing any system components, perform initialization and learning of related components (refer to the operations listed above). If initialization and learning are not performed, the transmission system will not function properly.
    3. Before proceeding with learning of the multi-mode manual transmission system, clear (initialize) the previously stored learning values. Since the multi-mode manual transmission system does not have an overwrite function, clearing (initializing) stored data is necessary to learn the system.


4.TROUBLESHOOTING INITIALIZATION AND LEARNING (ENGINE DOES NOT START)

HINT:
If any malfunctions are suspected in the transmission control system after reassembling or repairing transmission system components, perform troubleshooting in accordance with the following chart.


1.Check for DTC output
  1. Using an intelligent tester, check for output DTCs.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the tester ON.

    3. Select the following menu items: Powertrain / Multi-Mode M/T / DTC.

    4. Read any DTCs.

  2. Result:
    Result
    Proceed To
    No DTC output
    A
    DTC output
    B


B.
A

2.Check clutch position learning condition
  1. Check that the clutch position learning has been completed.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the tester ON.

    3. Select the following menu items: Powertrain / Multi-Mode M/T / Data List.

    4. Read the Learn-Clutch Stopper Point result.

  2. Result:
    Result
    Proceed To
    Exec (Executed)
    A
    Notexec (Not executed)
    B
    Fail (Failure)
    C


B.

C.
A

3.Check T/M gear position learning condition
  1. Check that the T/M gear position learning has been completed.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the tester ON.

    3. Select the following menu items: Powertrain / Multi-Mode M/T / Data List.

    4. Read the Learning-T/M results.

  2. Result:
    Result
    Proceed To
    Exec (Executed)
    A
    Notexec (Not executed)
    B
    Fail (Failure)
    C


B.

C.
A

4.Check whether gear is in neutral

  1. Referring to the shift slit position of the shift and select actuator, check whether the actual transmission gear position is in neutral.C121793E01

  2. Result:
    Result
    Proceed To
    Neutral
    A
    Other than Neutral
    B


B.
A

5.Check whether neutral position switch is ON
  1. Check whether the park/neutral position switch is ON (Click here).

  2. Result:
    Result
    Proceed To
    ON
    A
    OFF
    B


B.
A

6.Check whether T/M up-lock has occurred during gear position learning
  1. Check whether the T/M up-lock has occurred during gear position learning.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the tester ON.

    3. Select the following menu items: Powertrain / Multi-Mode M/T / Data List.

    4. Read the Possibility of T/M Uplock results.

  2. HINT:
    T/M up-lock: The transmission gear momentarily cannot be engaged due to mechanical reasons during gear position learning.

    Result:
    Result
    Proceed To
    No (Not occurred)
    A
    Yes (Occurred)
    B


B.
A


5.TROUBLESHOOTING INITIALIZATION AND LEARNING (VEHICLE DOES NOT START OFF)

HINT:
If any malfunctions are suspected in the transmission control system after reassembling or repairing transmission system components, perform troubleshooting in accordance with the following chart.


1.Check for DTC output
  1. Using an intelligent tester, check for output DTCs.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the tester ON.

    3. Select the following menu items: Powertrain / Multi-Mode M/T / DTC.

    4. Read any DTCs.

  2. Result:
    Result
    Proceed To
    No DTC output
    A
    DTC output
    B


B.
A

2.Check clutch position learning condition
  1. Check that the clutch position learning has been completed.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the tester ON.

    3. Select the following menu items: Powertrain / Multi-Mode M/T / Data List.

    4. Read the Learn-Clutch Stopper Point results.

  2. Result:
    Result
    Proceed To
    Exec (Executed)
    A
    Notexec (Not executed)
    B
    Fail (Failure)
    C


B.

C.
A

3.Check T/M gear position learning condition
  1. Check that the T/M gear position learning has been completed.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the tester ON.

    3. Select the following menu items: Powertrain / Multi-Mode M/T / Data List.

    4. Read the Learning-T/M results.

  2. Result:
    Result
    Proceed To
    Exec (Executed)
    A
    Notexec (Not executed)
    B
    Fail (Failure)
    C


B.

C.
A

4.Check clutch standby point learning condition
  1. Check that the clutch standby point learning has been completed.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the tester ON.

    3. Select the following menu items: Powertrain / Multi-Mode M/T / Data List.

    4. Read the Learn-Clutch Standby Point results.

  2. Result:
    Result
    Proceed To
    Exec (Executed)
    A
    Notexec (Not executed)
    B
    Fail (Failure)
    C


B.

C.
A

5.Confirm that gear position in [1st] or [R] when shift lever in [E], [M] or [R]
  1. Start the engine.

  2. Referring to the shift slit position of the shift and select actuator, check that the actual transmission gear position is in the 1st or R position when the shift lever position is changed from N to E, M or R.C121793E01


NG.
OK

6.Inspect accelerator pedal position sensor signal
  1. Check the accelerator pedal position sensor signal circuit.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the tester ON.

    3. Select the following menu items: Powertrain / Multi-Mode M/T / Data List.

    4. Check that the value of Accelerator Pedal Angle changes according to the accelerator pedal operation (Click here).

  2. Check the CAN communication circuit (Click here).

  3. Standard:
    Accelerator Pedal Operation
    Tester Display
    Fully depressed
    90 to 100 %
    Fully released
    0 to 10 %


NG.
OK

7.Rev up engine with transmission in neutral
  1. Check that the engine can be revved up when the transmission gear is in neutral.

  2. Result:
    Result
    Proceed To
    Possible
    A
    Impossible
    B


B.
A

8.Check whether T/M up-lock has occurred during gear position learning
  1. Check whether the T/M up-lock has occurred during gear position learning.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the tester ON.

    3. Select the following menu items: Powertrain / Multi-Mode M/T / Data List.

    4. Read the Possibility of T/M Uplock results.

  2. HINT:
    T/M up-lock: The transmission gear momentarily cannot be engaged due to mechanical reasons during gear position learning.

    Result:
    Result
    Proceed To
    No (Not occurred)
    A
    Yes (Occurred)
    B


B.
A

9.Check whether clutch disengaged when shift lever in [E], [M] or [R]
  1. Check the actual clutch state when the shift lever is in the E, M or R position.

  2. Result:
    Result
    Proceed To
    Disengaged
    A
    Not disengaged
    B


B.
A


6.PRECAUTIONS REGARDING USE OF SHIFT LOCK RELEASE BUTTON
  1. When the vehicle is parked with the shift lever in any position other than N:

    1. The engine cannot be started if the shift lever is moved to a position other than N by operating the shift lock release button.
      The shift lever should be moved back to the N position to start the engine.
    2. The engine cannot be started if the shift lever is in the position it was in when the vehicle was parked.
      The shift lever should be moved back to the N position to start the engine.
    3. When the shift lever is returned to the N position by operating the shift lock release button, the gear is shifted to neutral when the ignition switch is turned on (IG) so that the engine can be started.

  2. When the vehicle is parked with the shift lever in the N position:

    1. The engine can be started even if the shift lever is moved to a position other than N by operating the shift lock release button. In this case, the gear is shifted to the position in accordance with the shift lever position after the engine starts.
    Shift lever position when vehicle parked
    Current shift lever position
    Engine cranking operation
    Note
    Other than N
    Other than N*
    Impossible
    -
    Other than N
    Same position in when vehicle parked
    Impossible
    -
    Other than N
    N*
    Possible
    Gear shifted to neutral when ignition switch on (IG)
    N
    Other than N*
    Possible
    Gear shifted to position in accordance with shift lever position after engine start
    N
    N
    (Same position in when vehicle parked)
    Possible
    -
    *: The shift lever was moved with the shift lock release button operation.


7.OTHER PRECAUTIONS REGARDING MULTI-MODE MANUAL TRANSMISSION SYSTEM
  1. Set the gear in neutral when racing the engine.

  2. Set the gear to the neutral position before removing the shift and select actuator. If the gear cannot be shifted to the neutral position due to malfunctions of the actuator and/or transaxle gear, remove the plug from the shift and select actuator and observe the position of the shift slit within. If the slit is in a position other than neutral, use a screwdriver to set it to neutral.

    C121793E01

8.PRECAUTION REGARDING USE OF INTELLIGENT TESTER

NOTICE:
Observe the following items for safety reasons:
  1. Read its instruction books before using the tester.
  2. Prevent the tester cable from being caught on the pedals, shift lever and steering wheel when driving with the tester connected to the vehicle.
  3. When driving the vehicle for testing purposes using the tester, two people are required. One drives the vehicle, and the other operates the tester.

← INSTALLATION (from Nov 2005)PARTS LOCATION (from Nov 2005) →