2005-2008 Yaris · Service Manual ENGINE

P2112 Throttle Actuator Control System - Stuck Closed

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle body. The TP sensor provides feedback to the ECM in order that it can control the throttle actuator, and therefore the throttle valve, appropriately in response to driver inputs.

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.

DTC No.
DTC Detection Condition
Trouble Aria
P2112
The throttle does not open when current is applied to the throttle motor.
(1 trip detection logic)
  1. Open or short circuit in throttle motor circuit
  2. Throttle body assembly

HINT:
Detection for P2112 is performed during electronic throttle learning. (Detection is also performed in the case of electronic throttle learning using a tester).


WIRING DIAGRAM

A116140E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P2112)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P2112
    A
    P2112 and other DTCs
    B

    HINT:
    If any DTCs other than P2112 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. CHECK THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
  1. Check for contamination between the throttle valve and the housing.

    HINT:
    If necessary, clean the throttle body.

  1. Check that the throttle valve moves smoothly.

    OK:
    The throttle valve is not contaminated with foreign matter and moves smoothly.



NG
REPLACE THROTTLE BODY ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (THROTTLE BODY - ECM)
A120357E02
  1. Disconnect the throttle body connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    M+ (A32-2) - M+ (C39-4)
    Below 1 Ω
    M- (A32-3) - M- (C39-1)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    M+ (A32-2) or M+ (C39-4) - Body ground
    10 kΩ or higher
    M- (A32-3) or M- (C39-1) - Body ground
    10 kΩ or higher

  1. Reconnect the throttle body connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE THROTTLE BODY ASSEMBLY
  1. Replace the throttle body assembly.

  1. Perform electronic throttle learning (Click here).


NEXT

CHECK WHETHER DTC OUTPUT RECURS


← P2109 Throttle / Pedal Position Sensor "A" Minimum Stop Performance (from Aug 2005)P2119 Throttle Actuator Control Throttle Body Range / Performance (from Aug 2005) →