2005-2008 Yaris · Service Manual TRANSMISSION

P0725 Engine Speed Input Circuit

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

The ECM detects the engine revolution (NE) signal using the crankshaft position (CKP) sensor. The transmission control ECU controls the transmission in accordance with two engine revolution signals. One signal is received directly from the ECM through a serial communication line. The other signal is received from the ECM via the Controller Area Network (CAN) communication. If the transmission control ECU detects no engine revolution signals despite the engine revolution signal via CAN being received while the vehicle is running, the ECU interprets this as a malfunction in the engine revolution signal circuit. The ECU sets the DTC and illuminates the multi-mode manual transmission warning light.
DTC No.
DTC Detection Conditions
Trouble Areas
P0725
The transmission control ECU detects the following conditions simultaneously:
(1 trip detection logic)
  1. Engine speed is 400 rpm or less (serial communication circuit)
  2. Engine speed is 400 rpm or more (CAN communication circuit)
  3. Engine speed difference between signal from serial communication circuit and signal from CAN communication circuit is 400 rpm or more for 1.0 second
  1. Open or short in NE signal circuit
  2. Transmission control ECU
  3. ECM

WIRING DIAGRAM

C110752E02

INSPECTION PROCEDURE

NOTICE:
Only for 1KR-FE:
In ECM replacement, perform the electronic throttle learning after installing the ECM (Click here)


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0725)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Multi-Mode M/T / DTC.

  1. Read DTCs and write them down.

  1. Select the following menu items: Powertrain / Engine and ECT.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0725
    A
    P0725, and P0335, P0336 and/or P0339
    B

    Check the DTC output related to the engine revolution signal circuit in the engine control system and the multi-mode manual transmission control system. If DTC P0335, P0336 and/or P0339 are set together with DTC P0725, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. INSPECT TRANSMISSION CONTROL ECU ASSEMBLY
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Multi-Mode M/T / Data List / Backup Engine Speed.

  1. Check the engine speed value displayed on the tester.

    Items
    [Abbreviation]
    Measurement Items: Display
    Normal Conditions
    Diagnostic Notes
    Backup Engine Speed
    [Bacup Engin Spd]
    Back-up engine speed:
    Min.: 0 rpm, Max.: 8,160 rpm
    Approximately same as tachometer reading: Engine running
    0 rpm: Engine stopped
    0 rpm displayed when CAN communication mulfunctions

  1. C112732E03
    Connect the oscilloscope probes to the NE terminal and the body ground.

  1. Check the signal waveform.

    Tester Settings 
    Items
    Contents
    Terminals
    CH1: NE (A38-10) - Body ground
    Equipment Settings
    5 V/DIV, 5 ms/DIV
    Condition
    Engine idling

    OK:
    When the Backup Engine Speed indicates an idling speed on the intelligent tester, a waveform similar to that in the illustration is output.



OK
REPLACE TRANSMISSION CONTROL ECU ASSEMBLY
NG


3. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU - ECM)
C127407E01
  1. Disconnect the transmission control ECU connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance:
    Tester connections
    Specified Conditions
    1KR-FE:
    NE (A38-10) - NEO (C33-64)
    2SZ-FE:
    NE (A38-10) - NEO (A21-39)
    Below 1 Ω
    NE (A38-10) - Body ground
    10 kΩ or higher

  1. Reconnect the transmission control ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0715 Input / Turbine Speed Sensor Circuit Malfunction (from Nov 2005)P0806 Clutch Position Sensor Circuit (Range / Performance) (+ P0807, P0808) (from Nov 2005) →