2005-2008 Yaris · Service Manual TRANSMISSION

P0806 Clutch Position Sensor Circuit (Range / Performance)

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

The clutch stroke sensor is mounted on the clutch actuator, and detects the push rod position of clutch actuator. The sensor consists of a sensor arm, magnetic yoke and 2 Hall-ICs. This sensor is a non-contact type, and uses Hall-effect elements (Hall-ICs: main and sub), in order to yield accurate signals.
When the clutch actuator is operating, the magnetic yoke that is coaxially positioned on the sensor arm is rotated and the magnet position changes. The hall-ICs convert the magnet position change into the voltage signals and send them to the transmission control ECU. The transmission control ECU judges the clutch condition (whether the clutch is engaged, disengaged, or partially engaged) based on the signals from the clutch stroke sensor.
The main and sub circuits in the clutch stroke sensor have the same output characteristics.
C112730E02
DTC No.
DTC Detection Conditions
Trouble Areas
P0806
Deviation between sensor signal 1 (main) and sensor signal 2 (sub) is 2.0 mm (0.078 in.) or more for 1.0 second or more
(1 trip detection logic)
  1. Clutch stroke sensor
  2. Open or short in clutch stroke sensor circuit
  3. Transmission control ECU
P0807
Clutch stroke sensor (main) signal voltage is 0.2 V or less for 0.5 seconds or more
(1 trip detection logic)
  1. Clutch stroke sensor
  2. Open or short in clutch stroke sensor circuit
  3. Transmission control ECU
P0807
Clutch stroke sensor (sub) signal voltage is 0.2 V or less for 0.5 seconds or more
(1 trip detection logic)
  1. Clutch stroke sensor
  2. Open or short in clutch stroke sensor circuit
  3. Transmission control ECU
P0808
Clutch stroke sensor (main) signal voltage is 4.8 V or more for 0.5 seconds or more
(1 trip detection logic)
  1. Clutch stroke sensor
  2. Open or short in clutch stroke sensor circuit
  3. Transmission control ECU
P0808
Clutch stroke sensor (sub) signal voltage is 4.8 V or more for 0.5 seconds or more
(1 trip detection logic)
  1. Clutch stroke sensor
  2. Open or short in clutch stroke sensor circuit
  3. Transmission control ECU

WIRING DIAGRAM

C110753E05

INSPECTION PROCEDURE

NOTICE:
In clutch stroke sensor replacement, perform the initialization and learning of the multi-mode manual transmission system after installing the sensor (Click here).
If the sensor is installed without performing the initialization and learning, it may cause driving performance degradation or system component breakage.

HINT:
When only DTC P0806 is set, replace the clutch stroke sensor.


1. READ OUTPUT DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Multi-Mode M/T / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0806, P0807 and/or P0808
    A
    Only P0806
    B



B
REPLACE CLUTCH STROKE SENSOR
A


2. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and the tester ON.

  1. Select the following menu items: Powertrain / Multi-Mode M/T / Data List / Clutch Position (Current).

    Items
    [Abbreviation]
    Measurement Items: Display
    Normal Conditions
    Diagnostic Notes
    Clutch Position (Current)
    [Clutch Pos-Cur]
    Current clutch position:
    Min.: 0 mm, Max.: 127.998 mm
    19.0 mm (0.74 in.) to 44.0 mm (1.73 in.)
    Current clutch position displayed

    OK:
    The value on the tester is within the normal range.



OK
Go to step 4
NG


3. INSPECT CLUTCH STROKE SENSOR (MAIN)
C112722E03
  1. Remove the clutch stroke sensor.

  1. Measure the voltage between the terminals of the clutch stroke sensor connector (main).

    1. Prepare 3 dry cell batteries (1.5 V) and 2 leads for connecting the batteries and the sensor.

    2. Connect the batteries in series.

    3. Connect the positive battery terminal to sensor terminal 3, and the negative battery terminal to sensor terminal 2.

    4. Check the voltage between terminals 1 and 2.

      Standard voltage (combined dry cell battery voltage of 4.5 V):
      Sensor Angle
      Terminal (1-2) Output Voltage
      55°
      Approximately 4.05 V
      0°
      Approximately 2.25 V
      -55°
      Approximately 0.45 V

      Reference voltage (combined dry cell battery voltage of 5.0 +- 0.3 V):
      Sensor Angle
      Terminal (1-2) Output Voltage
      55°
      Approximately 4.5 V
      0°
      Approximately 2.5 V
      -55°
      Approximately 0.5 V

      NOTICE:
      1. Do not apply more than 6 V
      2. Do not use a sensor which has been dropped.

  1. Reinstall the clutch stroke sensor (Click here).

  1. Perform initialization and learning (Click here).



NG
REPLACE CLUTCH STROKE SENSOR
OK


4. INSPECT CLUTCH STROKE SENSOR (SUB)
  1. Remove the clutch stroke sensor.

  1. C112722E04
    Measure the voltage between the terminals of the clutch stroke sensor connector (sub).
    1. Prepare 3 dry cell batteries (1.5 V) and 2 leads for connecting the batteries and the sensor.

    2. Connect the batteries in series.

    3. Connect the positive battery terminal to sensor terminal 6, and the negative battery terminal to sensor terminal 5.

    4. Check the voltage between terminals 4 and 5.

      Standard voltage (combined dry cell battery voltage of 4.5 V):
      Sensor Angle
      Terminal (4-5) Output Voltage
      55°
      Approximately 4.05 V
      0°
      Approximately 2.25 V
      -55°
      Approximately 0.45 V

      Reference voltage (combined dry cell battery voltage of 5.0 +- 0.3 V):
      Sensor Angle
      Terminal (4-5) Output Voltage
      55°
      Approximately 4.5 V
      0°
      Approximately 2.5 V
      -55°
      Approximately 0.5 V

      NOTICE:
      1. Do not apply more than 6 V
      2. Do not use a sensor which has been dropped.

  1. Reinstall the clutch stroke sensor (Click here).

  1. Perform initialization and learning (Click here).



NG
REPLACE CLUTCH STROKE SENSOR
OK


5. CHECK HARNESS AND CONNECTOR (CLUTCH STROKE SENSOR - TRANSMISSION CONTROL ECU)
C113919E09
  1. Disconnect the clutch stroke sensor connector.

  1. Disconnect the transmission control ECU connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    VCR2 (A38-35) - (A40-6)
    Below 1 Ω
    VSR2 (A38-34) - (A40-4)
    Below 1 Ω
    E2R2 (A38-33) - (A40-5)
    Below 1 Ω
    VCR1 (A38-27) - (A40-3)
    Below 1 Ω
    VSR1 (A38-26) - (A40-1)
    Below 1 Ω
    E2R1 (A38-25) - (A40-2)
    Below 1 Ω
    VCR2 (A38-35) - Body ground
    10 kΩ or higher
    VSR2 (A38-34) - Body ground
    10 kΩ or higher
    E2R2 (A38-33) - Body ground
    10 kΩ or higher
    VCR1 (A38-27) - Body ground
    10 kΩ or higher
    VSR1 (A38-26) - Body ground
    10 kΩ or higher
    E2R1 (A38-25) - Body ground
    10 kΩ or higher

  1. Reconnect the clutch stroke sensor connector.

  1. Reconnect the transmission control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY


← P0725 Engine Speed Input Circuit (from Nov 2005)P0810 Clutch Position Control Error (from Nov 2005) →