B1662/45 Indicator Light Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2006
Versions by build date: Aug 2005 – Dec 2005 from Jan 2006
DESCRIPTION
The indicator light circuit consists of the center airbag sensor assembly and the combination meter. DTC B1662/45 is set when a malfunction is detected in the indicator light circuit.| DTC No. |
DTC Detecting Conditions |
Trouble Areas |
| B1662/45 |
|
|
WIRING DIAGRAM






INSPECTION PROCEDURE
- NOTICE:
- In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.
- Turn the ignition switch off.
- Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
- Disconnect the connector from the center airbag sensor assembly.
- Disconnect the connector from the steering pad.
- Disconnect the connector from the front seat outer belt assembly LH.
- Disconnect the connector from the front seat outer belt assembly RH.
- HINT:
- Skip the following steps if side airbags, curtain shield airbags, front passenger airbag and a knee airbag are not fitted.
- Disconnect the connector from the front passenger airbag assembly.
- Disconnect the connector from the front seat side airbag assembly LH.
- Disconnect the connector from the front seat side airbag assembly RH.
- Disconnect the connector from the curtain shield airbag assembly LH.
- Disconnect the connector from the curtain shield airbag assembly RH.
- Disconnect the connector from the driver side knee airbag assembly.
| 1. CHECK DTC (AIRBAG SYSTEM) |
Turn the ignition switch on (IG).
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG) and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1662/45 is not output.
- HINT:
- DTCs other than B1662/45 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK DTC (CAN COMMUNICATION SYSTEM) |
Turn the ignition switch on (IG).
Check the DTCs (Click here).
- OK:
- DTC is not output.
|
|
||||
| OK | |
| 3. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the combination meter.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 4. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() ![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly.
- for HATCHBACK; (Click here )
- for SEDAN; (Click here )
- HINT:
- Perform the inspection using parts from a normal vehicle when possible.
- for HATCHBACK; (Click here )
Connect the connectors to the center airbag sensor assembly and the combination meter.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1662/45 is not output.
- HINT:
- DTCs other than B1662/45 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||

