2005-2008 Yaris · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Nov 2005


INSPECT ENGINE COOLANT
  1. The engine coolant should be between the LOW and FULL lines when the engine is cold.

    HINT:
    If it is below the LOW line, check for leakage and add Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology up to the FULL line.


INSPECT ENGINE OIL
  1. Warm up the engine, then stop the engine and wait for 5 minutes. Check that the engine oil level is between the low and full marks on the oil level gauge.
    If the engine oil level is low, check for oil leakage and add engine oil up to the full level mark.

    NOTICE:
    Do not add engine oil to above the full level mark.


INSPECT BATTERY
  1. Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.

  1. Check the volume of electrolyte in each cell.

    1. For batteries that are maintenance-free:

      1. If the electrolyte volume is below the lower line, replace the battery.
      2. If the electrolyte volume is above the lower line, check the battery voltage when cranking the engine.
      3. If the voltage is less than 9.6 V, recharge or replace the battery.

        HINT:
        Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, etc.).

    2. For batteries that are not maintenance-free:

      1. If the electrolyte volume is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte specific gravity.

      Standard specific gravity:
      1.25 to 1.29 at 20 °C (68°F)

      If the electrolyte volume is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery.

      HINT:
      Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).


INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly.

  1. Visually check that there is no dirt, blockages, or damage to the air cleaner filter element.

    HINT:
    1. If there is any dirt or a blockage in the air cleaner filter element, clean it with compressed air.
    2. If any dirt or a blockage remains even after cleaning the air cleaner filter element with compressed air, replace it.


INSPECT SPARK PLUG

INSPECT IGNITION TIMING

  1. When using an intelligent tester:

    1. Warm up and stop the engine.

    2. A127178E01
      Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG).

    4. Select the following menu items:
      Powertrain / Engine and ECT / Active Test / TC (TE1) / ON.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    5. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      1. Turn all the electrical systems and the A/C off.
      2. Inspect the ignition timing with the cooling fan off.
      3. When checking the ignition timing, shift the transmission to the neutral position.

    6. Select the following menu items: TC (TE1) / OFF

    7. Turn the ignition switch off.

    8. Disconnect the intelligent tester from the DLC3.

  1. When not using an intelligent tester:

    1. Remove the air cleaner cap sub-assembly (Click here).

    2. A127234
      Pull out the wire harness shown in the illustration.

      NOTICE:
      After checking, wrap the wire harness with tape.

    3. Warm up and stop the engine.

    4. Connect the clip of the timing light to the wire harness.

      NOTICE:
      Use a timing light that detects the first signal.

    5. Turn the ignition switch on (IG).

    6. A082779E23
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  

      NOTICE:
      Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    7. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      1. Turn all the electrical systems and the A/C off.
      2. Inspect the ignition timing with the cooling fan off.
      3. When checking the ignition timing, shift the transmission to the neutral position.

    8. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    9. Turn the ignition switch off.

    10. Remove the timing light.

    11. Install the air cleaner cap sub-assembly (Click here).


INSPECT ENGINE IDLING SPEED

  1. When using an intelligent tester:

    1. Warm up and stop the engine.

    2. A127178E01
      Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG).

    4. Select the following menu items: Powertrain / Engine and ECT /Data List / Engine Speed.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    5. Inspect the engine idling speed.

      Idling speed:
      550 to 650 rpm (for Manual Transaxle)
      550 to 650 rpm (for Multi-Mode Manual Transaxle)

      NOTICE:
      1. Turn all the electrical systems and the A/C off.
      2. Inspect the idling speed with the cooling fan off.
      3. When checking the idling speed, shift the transmission to either the neutral position or the parking position.

    6. Turn the ignition switch off.

    7. Disconnect the intelligent tester from the DLC3.

  1. When not using an intelligent tester.

    1. Warm up and stop the engine.

    2. A082779E24
      Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.
      SST
      09843-18040  

      NOTICE:
      Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    3. Turn the ignition switch on (IG).

    4. Inspect the engine idling speed.

      Idling speed:
      600 to 700rpm

    5. Turn the ignition switch off.

    6. Disconnect the tachometer.

    7. Remove SST from terminal 9 (TAC).


INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Remove the air cleaner cap sub-assembly (Click here).

  1. Remove the 4 ignition coils (Click here).

  1. Remove the 4 spark plugs.

  1. Disconnect the 4 fuel injector connectors.

  1. A108947
    Inspect the cylinder compression pressure.

    1. Insert a compression gauge into the spark plug hole.

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Compression:
      1,176 kPa (12.0 kgf/cm2, 171psi)

      Minimum pressure:
      931 kPa (9.5 kgf/cm2, 134 psi)

      Difference between cylinders:
      98 kPa (1.0 kgf/cm2, 14 psi) or less

      NOTICE:
      1. Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.
      2. Inspect the other cylinders in the same way.
      3. Measure the compression in as short a time as possible.

    4. If the cylinder compression is low, pour a light coat of engine oil into the cylinder through the spark plug hole, then inspect it again.

      HINT:
      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      2. If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.

  1. Connect the 4 fuel injector connectors.

  1. Install the 4 spark plugs.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the 4 ignition coils (Click here).

  1. Install the air cleaner cap sub-assembly (Click here).


INSPECT CO/HC
  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.

  1. Check the CO/HC concentration during idling and when running at 2,500 rpm.

    HINT:
    When doing the 2 mode (with the engine idling/running at 2,500 rpm) test, the measuring procedures are determined by applicable local regulations.

    If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.

    1. Check the heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

      CO
      HC
      Problems
      Possible Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        2. Dirty, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leakage from intake and exhaust valves
      4. Leakage from cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idling
      (Black smoke from exhaust)
      1. Restricted air cleaner filter element
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        2. Faulty engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Throttle body

← PRECAUTION (from Nov 2005)COMPONENTS (from Nov 2005) →