2005-2008 Yaris · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Nov 2006


INSPECT ENGINE COOLANT
  1. Remove the radiator cap sub-assembly.

    CAUTION:
    To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Check for excessive deposits of rust or scale around the radiator cap sub-assembly and radiator filler hole. The engine coolant should be free of oil.
    If excessively dirty, replace the engine coolant.

  1. Reinstall the radiator cap sub-assembly.


INSPECT ENGINE OIL
  1. Check the oil for deterioration, water intrusion, discoloration or thinning.
    If the quality is visibly poor, replace the oil and oil filter.


INSPECT BATTERY
  1. Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.

  1. Check the volume of electrolyte in each cell.

    1. For batteries that are maintenance-free:

      1. If the electrolyte volume is below the lower line, replace the battery.
      2. If the electrolyte volume is above the lower line, check the battery voltage when cranking the engine.
      3. If the voltage is less than 9.6 V, recharge or replace the battery.

      HINT:
      Before checking the battery voltage, turn off all electrical systems (headlights, blower motor, etc.).

    2. For batteries that are not maintenance-free:

      1. If the electrolyte volume is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte specific gravity.

      Standard specific gravity:
      1.25 to 1.29 at 20 °C ( 68°F)

      If the electrolyte volume is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery.

      HINT:
      Before checking the battery voltage, turn off all electrical systems (headlights, blower motor, rear defogger, etc.).


INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly.

  1. Visually check that there is no dirt, blockage, or damage to the air cleaner filter element.

    HINT:
    1. If there is any dirt or blockages in the air cleaner filter element, clean it with compressed air.
    2. If any dirt or blockages remain even after cleaning the air cleaner filter element with compressed air, replace it.


INSPECT SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.

  1. I039522E11
    Check the electrode.

    1. Using a megaohmmeter, measure the insulation resistance.

      Standard resistance:
      10 MΩ or more

      HINT:
      1. If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
      1. If a megaohmmeter is not available, perform the following simple inspection instead.

  1. Alternative inspection method.

    1. Quickly accelerate the engine to 4,000 rpm 5 times.

    2. Remove the spark plug.

    3. B001301E01
      Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage to its thread and insulator.
    If there is damage, replace the spark plug.

    Recommended spark plug:
    Manufacturer
    Product
    DENSO
    SC20HR11

  1. B002101E04
    Check the spark plug electrode gap.

    Maximum electrode gap for used spark plug:
    1.3 mm (0.051 in.)

    If the gap is greater than the maximum, replace the spark plug.

    Electrode gap for new spark plug:
    1.0 to 1.1 mm (0.039 to 0.043 in.)

  1. Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Air pressure:
    588 kPa (6 kgf/cm2, 85 psi)

    Duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.


INSPECT IGNITION TIMING

  1. When using an intelligent tester:

    1. Warm up and stop the engine.

    2. A117072E02
      Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG).

    4. Select the following menu items:
      Powertrain / Engine and ECT / Active Test / TC (TE1) / ON.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    5. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      1. Turn all electrical systems and the A/C off.
      2. Inspect the ignition timing with the cooling fan off.
      3. When checking the ignition timing, shift the transmission to the neutral position.

    6. Select the following menu items: TC (TE1) / OFF

    7. Turn the ignition switch off.

    8. Disconnect the intelligent tester from the DLC3.

  1. When not using an intelligent tester:

    1. Remove the No. 2 cylinder head cover (Click here).

    2. A150576
      Pull out the wire harness (brown) shown in the illustration.

      NOTICE:
      After checking, wrap the wire harness with tape.

    3. Warm up and stop the engine.

    4. Connect a timing light clip to the wire harness.

      NOTICE:
      Use a timing light that detects the first signal.

    5. Turn the ignition switch on (IG).

    6. A082779E23
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  

      NOTICE:
      Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    7. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      1. Turn all electrical systems and the A/C off.
      2. Inspect the ignition timing with the cooling fan off.
      3. When checking the ignition timing, shift the transmission to the neutral position.

    8. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    9. Turn the ignition switch off.

    10. Remove the timing light.

    11. Install the No. 2 cylinder head cover (Click here).


INSPECT ENGINE IDLING SPEED

  1. When using an intelligent tester:

    1. Warm up and stop the engine.

    2. A117072E02
      Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG).

    4. Select the following menu items: Powertrain / Engine and ECT /Data List / Engine Speed.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    5. Inspect the engine idling speed.

      Idling speed:
      600 to 700rpm

      NOTICE:
      1. Turn all electrical systems and the A/C off.
      2. Inspect the idling speed with the cooling fan off.
      3. When checking the idling speed, shift the transmission to either the neutral position or the parking position.

    6. Turn the ignition switch off.

    7. Disconnect the intelligent tester from the DCL3.

  1. When not using an intelligent tester:

    1. Warm up and stop the engine.

    2. A082779E24
      Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.
      SST
      09843-18040  

      NOTICE:
      Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    3. Turn the ignition switch on (IG).

    4. Inspect the engine idling speed.

      Idling speed:
      600 to 700rpm

    5. Turn the ignition switch off.

    6. Disconnect the tachometer.

    7. Remove SST from terminal 9 (TAC).


INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Remove the No. 2 cylinder head cover (Click here).

  1. Remove the 4 ignition coils (Click here).

  1. Remove the 4 spark plugs.

  1. Disconnect the 4 fuel injector connectors.

  1. A156613
    Inspect the cylinder compression pressure.

    1. Insert a compression gauge into the spark plug hole.

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Compression:
      1373 kPa (14.0 kgf/cm2, 199 psi)

      Minimum pressure:
      1079 kPa (11.0 kgf/cm2, 156 psi)

      Difference between each cylinder:
      98 kPa (1.0 kgf/cm2, 14 psi) or less

      NOTICE:
      1. Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.
      2. Inspect the other cylinders in the same way.
      3. Measure the compression in as short a time as possible.

    4. If the cylinder compression is low, pour a light coat of engine oil into the cylinder through the spark plug hole, then inspect it again.

      HINT:
      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      2. If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.

  1. Connect the 4 fuel injector connectors.

  1. Install the 4 spark plugs.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the 4 ignition coils (Click here).

  1. Install the No. 2 cylinder head cover (Click here).


INSPECT CO/HC
  1. Start the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.

  1. Check the CO/HC concentration during idling and when running at 2500 rpm.

    HINT:
    When doing the 2 mode (with the engine idling/running at 2500 rpm) test, the measuring procedures are determined by applicable local regulations.

    If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.

    1. Check the heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

      CO
      HC
      Problems
      Possible Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        2. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leakage from intake and exhaust valves
      4. Leakage from cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idling
      (Black smoke from exhaust)
      1. Restricted air cleaner filter element
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        2. Faulty engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Throttle body

← PRECAUTION (from Nov 2006)COMPONENTS (from Nov 2006) →