INSTALLATION
Removal / installation · Vehicles built from Nov 2006
| 1. INSTALL WATER PUMP ASSEMBLY |
Install a new water pump gasket to the timing chain cover.

- HINT:
- Make sure that the installation surfaces are clean.
Install the water pump assembly with the 5 bolts.

Bolt length Item
Length
Bolt A
35 mm (1.38 in.)
Bolt B
18 mm (0.71 in.)
- Torque:
- 21 N*m{ 214 kgf*cm , 16 ft.*lbf } (for bolt A)
- 24 N*m{ 240 kgf*cm , 17 ft.*lbf } (for bolt B)
| 2. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
Install the engine moving control rod with the through bolt.
- Torque:
- 120 N*m{ 1224 kgf*cm , 89 ft.*lbf }
Remove the 2 bolts and remove the 2 engine hangers.
| 3. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE |
Set the engine assembly with transaxle and front suspension crossmember on the engine lifter.

Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the engine mounting insulator RH and LH can be installed.
Install the engine mounting insulator LH with the through bolt and nut.

- Torque:
- 52 N*m{ 530 kgf*cm , 38 ft.*lbf }
Install the engine mounting insulator RH with the 6 bolts and nut.

- Torque:
- 88 N*m{ 897 kgf*cm , 65 ft.*lbf } for Bolt A
- 45 N*m{ 459 kgf*cm , 33 ft.*lbf } for Bolt B
- 52 N*m{ 530 kgf*cm , 38 ft.*lbf } for Nut C
Install the engine mounting stay RH with the 2 bolts.

- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
Operate the engine lifter and provisionally install the engine assembly with transaxle and front suspension crossmember onto the vehicle with the 6 bolts.
Insert SST into the datum holes in the front suspension crossmember RH and LH alternately and tighten bolts A, B and C on both sides in several sequences.



- SST
- 09670-00010
- Torque:
- 70 N*m{ 714 kgf*cm , 52 ft.*lbf } for Bolt A
- 160 N*m{ 1631 kgf*cm , 118 ft.*lbf } for Bolt B
- 95 N*m{ 969 kgf*cm , 70 ft.*lbf } for Bolt C
- CAUTION:
- Insert SST into the datum hole vertically.
- If impossible to insert SST vertically, loosen all bolts and then insert SST again.
- Insert SST into the datum hole vertically.
| 4. INSTALL FRONT AXLE ASSEMBLY LH |
Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.
- NOTICE:
- Do not push the front axle further out of the vehicle than is necessary.
- Do not damage the outboard joint boot.
- Check for any foreign matter on the speed sensor rotor and insertion part.
- Do not damage the speed sensor rotor.
- Do not push the front axle further out of the vehicle than is necessary.
| 5. INSTALL FRONT AXLE ASSEMBLY RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 6. INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH |
Install the lower arm onto the steering knuckle with a new castle nut.

- Torque:
- 98 N*m{ 1000 kgf*cm , 72 ft.*lbf }
- NOTICE:
- If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.
Install a new clip.
| 7. INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 8. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
Install the stabilizer link with the nut.

- Torque:
- 74 N*m{ 755 kgf*cm , 55 ft.*lbf }
- HINT:
- If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.
| 9. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 10. INSTALL TIE ROD END SUB-ASSEMBLY LH |
Install the tie rod end onto the steering knuckle with a new castle nut.

- Torque:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
- NOTICE:
- If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.
Install a new cotter pin.
| 11. INSTALL TIE ROD END SUB-ASSEMBLY RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 12. INSTALL SPEED SENSOR FRONT LH |
![]() ![]() |
Install the speed sensor onto the steering knuckle with the bolt.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
- NOTICE:
- Check that the speed sensor tip and installation portion are free of foreign matter.
- Install the speed sensor without turning it from its original installation angle.
- Check that the speed sensor tip and installation portion are free of foreign matter.
Install the flexible hose and speed sensor with the bolt.

- Torque:
- 29 N*m{ 300 kgf*cm , 22 ft.*lbf }
- NOTICE:
- Install the flexible hose and speed sensor without twisting them.
| 13. INSTALL SPEED SENSOR FRONT RH |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 14. INSTALL FRONT AXLE SHAFT LH NUT |
![]() ![]() |
Using a 30 mm socket wrench, install a new axle hub nut.
- Torque:
- 216 N*m{ 2203 kgf*cm , 160 ft.*lbf }
Using a chisel and hammer, caulk the axle hub nut.
| 15. INSTALL FRONT AXLE SHAFT RH NUT |
- HINT:
- The installation procedure for the RH side is the same as that for the LH side.
| 16. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Using vernier calipers, measure the free length of the compression spring.

- Minimum length (Front side):
- 40.5 mm (1.594 in.)
- Minimum length (Rear side):
- 38.5 (1.516 in.)
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

- NOTICE:
- Install the exhaust pipe gasket in the correct direction.
- Do not damage the outer surface of the exhaust pipe gasket.
- Do not reuse the exhaust pipe gasket.
- Do not push in the gasket with the exhaust pipe when connecting it.
- Install the exhaust pipe gasket in the correct direction.
Install the 3 exhaust pipe support No. 4.
Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.
- Torque:
- 43 N*m{ 439 kgf*cm , 32 ft.*lbf }
| 17. INSTALL HEATED OXYGEN SENSOR |
Using SST, install the heated oxygen sensor onto the front exhaust pipe.

- SST
- 09224-00010
- Torque:
- 44 N*m{ 449 kgf*cm , 33 ft.*lbf }
Pass the sensor connector through the floor panel and install the grommet.
Install the wire harness clamp bracket.

Connect the heated oxygen sensor connector.

| 18. INSTALL REAR CONSOLE BOX ASSEMBLY |
![]() ![]() |
Engage the 2 clips and install the console box rear.
Install bolt <F>.
| 19. INSTALL CONSOLE BOX REAR COVER |
![]() ![]() |
Engage the 8 claws and install the console box rear cover.
| 20. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY |
![]() ![]() |
Engage the 6 claws and install the shifting hole cover.
| 21. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() ![]() |
Install the shift lever knob.
| 22. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
Install clip B onto the body portion and install column No. 1 onto the body portion with clip A.

- NOTICE:
- Make sure that the lip portion of hole cover No. 1 is not damaged.
| 23. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() ![]() |
Align the matchmarks and install the sliding yoke onto the intermediate shaft.
- Torque:
- 28 N*m{ 290 kgf*cm , 21 ft.*lbf }
Tighten bolt A.
- Torque:
- 28 N*m{ 290 kgf*cm , 21 ft.*lbf }
| 24. INSTALL COLUMN HOLE COVER SILENCER SHEET |
![]() ![]() |
Install the column hole cover silencer sheet with the 2 clips.
Install the floor carpet.
| 25. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY |
![]() ![]() |
Install the clutch release cylinder and clutch pipe with the 4 bolts.
- Torque:
- 12 N*m{ 120 kgf*cm , 8.7 ft.*lbf } for bolt A
- 12 N*m{ 122 kgf*cm , 8.9 ft.*lbf } for bolt B
| 26. CONNECT FUEL TUBE SUB-ASSEMBLY |
Connect the fuel tube connector and fuel pipe, and install the No. 1 fuel pipe clamp.

- CAUTION:
- Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a click sound. If the connection is tight, apply a small amount of engine oil to the the tip of the pipe. After connecting, pull the pipe and connector to make sure that they are securely connected.
| 27. CONNECT HEATER WATER INLET HOSE A |
Install heater water inlet hose A with the clip.

| 28. CONNECT HEATER WATER OUTLET HOSE A(FROM HEATER UNIT) |
Install heater water outlet hose A with the clip.

| 29. CONNECT ENGINE WIRE |
Connect the 2 engine wire harness connectors and wire harness clamp to the engine room junction block.

Connect the engine wire harness connector to the ECM.

Connect the wire harness clamp.
Connect the 2 connectors.

Install the transaxle earth wire with the bolt.

- Torque:
- 26 N*m{ 260 kgf*cm , 19 ft.*lbf }
Connect the 2 wire harness clamps.
| 30. INSTALL NO. 1 FUEL VAPOR FEED HOSE |
Install the No. 1 fuel vapor feed hose into the vacuum switching valve assembly.

| 31. INSTALL UNION TO CHECK VALVE HOSE |
Install the union to check valve hose with the clip.

| 32. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() ![]() |
Connect the 2 cable ends and install the 2 washers and the 2 clips.
Install 2 new clips onto the control cable bracket.
| 33. INSTALL WITH PULLEY COMPRESSOR ASSEMBLY |
![]() ![]() |
Using "TORX" socket wrench E8, install the compressor with the 2 stud bolts.
- Torque:
- 15 N*m{ 153 kgf*cm , 11 ft.*lbf }
Tighten the compressor with the 2 bolts and 2 nuts.

- Torque:
- 25 N*m{ 250 kgf*cm , 18 ft.*lbf }
- NOTICE:
- Tighten the bolts in the following order: 1 (provisional tightening) → 2 → 3 → 4 → 1.
Connect the connector and the clamp.
| 34. INSTALL RADIATOR ASSEMBLY |
![]() ![]() |
Engage the 2 claws and install the radiator assembly onto the vehicle.
- NOTICE:
- Do not apply excessive force to the cooler condenser assembly or piping when installing the radiator assembly.
Connect the cooling fan motor connector and wire harness clamp.

| 35. INSTALL FAN SHROUD VENTILATION DUCT ASSEMBLY |
![]() ![]() |
Engage the 4 claws and install the fan shroud ventilation duct assembly.
- NOTICE:
- Do not apply excessive force to the cooler condenser assembly or piping when installing the radiator assembly.
| 36. INSTALL RADIATOR SUPPORT SUB-ASSEMBLY |
![]() ![]() |
Install the radiator support sub-assembly upper with the 4 bolts.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
Connect the horn assembly connector.

| 37. INSTALL HOOD LOCK ASSEMBLY |
![]() ![]() |
Install the hood lock assembly with the 3 bolts.
- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
Install the hood lock control cable assembly with the 2 clamps.

| 38. CONNECT NO. 1 RADIATOR HOSE |
![]() ![]() |
Connect the No. 1 radiator hose with the clip.
| 39. INSTALL NO. 2 RADIATOR HOSE |
Install the No. 2 radiator hose with the 2 clips.

| 40. INSTALL FRONT BUMPER COVER |
Install the 2 clips, the 2 spring nuts and the screw grommet.

Connect the 2 fog light connectors.

Engage the 6 claws and install the front bumper cover.
Install the 7 clips.

Install the 2 screw grommets.

Install the 5 screws and the 3 bolts.
Remove the protective tape.

| 41. INSTALL FAN AND GENERATOR V BELT |
Provisionally install the fan and generator V belt onto each pulley.
- NOTICE:
- Make sure that the V belt is securely fitted into the rib groove of the pulley.
| 42. ADJUST FAN AND GENERATOR V BELT |
Turn adjusting bolt C and adjust the tension of the V belt.

- NOTICE:
- Check that bolt D is tightened to the specified torque of 19 N*m (189 kgf*cm, 14 ft.*lbf).
Tighten fixing bolts A and B.
- Torque:
- 19 N*m{ 189 kgf*cm , 14 ft.*lbf } for bolt A
- 43 N*m{ 438 kgf*cm , 32 ft.*lbf } for bolt B
| 43. INSPECT FAN AND GENERATOR V BELT |
Check the V belt deflection and tension.

- Deflection:
Item
Specified Condition
New belt
7.5 to 8.6 mm (0.296 to 0.338 in.)
Used belt
8.0 to 10.0 mm (0.315 to 0.397 in.)
- Tension:
Item
Specified Condition
New belt
688 to 884 N (70 to 90 kg, 155 to 199 ld)
Used belt
402 to 598 N (40 to 61 kg, 90 to 134 ld)
- HINT:
- Check the V belt deflection at the specified point.
- When installing a new belt, set its tension to the specified value.
- When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.
- When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of the Used Belt specifications.
- V belt tension and deflection should be checked after 2 revolutions of engine cranking.
- When checking the tension, use a sonic tension meter.
- Check the V belt deflection at the specified point.
- Weight:
- 15 g/rib*m
- Width:
- 6 ribs (21.36 mm)
- Span:
- 188 mm (w/ A/C)
- 282 mm (w/o A/C)
| 44. INSTALL NO. 2 CYLINDER HEAD COVER |
Disengage the 4 fittings shown and install the No. 2 cylinder head cover by applying pressure to it.

- HINT:
- Make sure that the oil and the engine oil level dipstick are correctly installed before installing the No. 2 cylinder head cover.
| 45. INSTALL BATTERY CARRIER |
![]() ![]() |
Install the battery carrier with the 5 bolts.
- Torque:
- 17 N*m{ 173 kgf*cm , 13 ft.*lbf }
Install the clamp.
| 46. INSTALL AIR CLEANER BRACKET |
![]() ![]() |
Install the air cleaner bracket with the 2 bolts.
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf }
Connect the wire harness clamp to the air cleaner bracket.
| 47. INSTALL AIR CLEANER ASSEMBLY |
![]() ![]() |
Install the air cleaner case with air cleaner inlet with the 2 bolts.
- Torque:
- 7.8 N*m{ 80 kgf*cm , 69 in.*lbf }
Connect the wire harness to the air cleaner case.
Install the air cleaner element.
Install and lock the air cleaner cap with air cleaner hose and then tighten the air cleaner hose clamp.

- Torque:
- 3.0 N*m{ 31 kgf*cm , 27 in.*lbf }
Connect the ventilation hose to the air cleaner hose.
Connect the intake air flow meter connector and wire harness clamp.
| 48. INSTALL COWL TOP PANEL OUTER |
![]() ![]() |
Install the cowl top panel with the 9 bolts.
- Torque:
- 6.5 N*m{ 66 kgf*cm , 58 in.*lbf }
Connect the wire harness clamp.

| 49. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY |
![]() ![]() |
Engage the claw to install No. 2 cowl to register duct.
| 50. INSTALL FRONT WIPER MOTOR AND LINK |
![]() ![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
| 51. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD) |
![]() ![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the 2 clips.
| 52. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
![]() ![]() |
Connect the washer hose.
Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

Install the clip.
Connect the washer hose.
Engage the 2 hooks and install cowl top ventilator louver center No. 1.

| 53. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD) |
![]() ![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the clip.
| 54. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
![]() ![]() |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 55. INSTALL HOOD TO COWL TOP SEAL |
![]() ![]() |
Engage the 7 clips and install the hood to cowl top seal.
| 56. INSTALL FRONT WIPER ARM LH |
![]() ![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
| 57. INSTALL FRONT WIPER ARM RH |
![]() ![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
| 58. INSTALL FRONT WIPER ARM HEAD CAP |
![]() ![]() |
Engage the claw and install the 2 front wiper arm head caps.
| 59. INSTALL BATTERY TRAY |
| 60. INSTALL BATTERY |
Install the battery onto the vehicle with the battery clamp.
- Torque:
- 3.5 N*m{ 36 kgf*cm , 31 in.*lbf }
Connect the cable to the battery terminal.
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 61. ADD ENGINE COOLANT |
Tighten all the plugs.
Pour engine coolant into the radiator assembly until it is completely full.
- Capacity:
- 5.0 liters (5.3 USqts, 4.4 lmp. qts)
- NOTICE:
- Do not substitute water for engine coolant.
- HINT:
- Use of improper engine coolant may damage the engine coolant system.
- Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Use of improper engine coolant may damage the engine coolant system.
Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.
Install the radiator cap sub-assembly securely.
Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens.
While the thermostat is open, circulate the coolant for several minutes.- HINT:
- The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.
Maintain the engine speed at 2500 to 3000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
- CAUTION:
- When pressing the radiator hoses:
- Wear protective gloves.
- Be careful as the radiator hoses are hot.
- Keep your hands away from the radiator fan.
- Wear protective gloves.
Stop the engine and wait until the coolant cools down.
If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.
Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add engine coolant.
| 62. INSPECT FOR FUEL LEAK |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and the intelligent tester main switch ON.
- NOTICE:
- Do not start the engine.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.
Check that there is no fuel leakage anywhere in the fuel system after doing maintenance.
| 63. INSPECT FOR ENGINE OIL LEAK |
| 64. INSPECT FOR EXHAUST GAS LEAK |
| 65. INSPECT FOR ENGINE COOLANT LEAK |
- CAUTION:
- To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.
Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
| 66. INSTALL ENGINE UNDER COVER RH |
| 67. INSTALL ENGINE UNDER COVER LH |
| 68. INSTALL FRONT WHEELS |
| 69. INSPECT IGNITION TIMING |
When using an intelligent tester:
Warm up and stop the engine.
Connect the intelligent tester to the DLC3.

Turn the ignition switch on (IG).
Select the following menu items:
Powertrain / Engine and ECT / Active Test / TC (TE1) / ON.- HINT:
- Refer to the intelligent tester operator's manual for further details.
Inspect the ignition timing during idling.
- Ignition timing:
- 8 to 12 degrees BTDC
- NOTICE:
- Turn all electrical systems and the A/C off.
- Inspect the ignition timing with the cooling fan off.
- When checking the ignition timing, shift the transmission to the neutral position.
- Turn all electrical systems and the A/C off.
Select the following menu items: TC (TE1) / OFF
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using an intelligent tester:
Remove the No. 2 cylinder head cover (Click here).
Pull out the wire harness (brown) shown in the illustration.

- NOTICE:
- After checking, wrap the wire harness with tape.
Warm up and stop the engine.
Connect a timing light clip to the wire harness.
- NOTICE:
- Use a timing light that detects the first signal.
Turn the ignition switch on (IG).
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

- SST
- 09843-18040
- NOTICE:
- Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
Inspect the ignition timing during idling.
- Ignition timing:
- 8 to 12 degrees BTDC
- NOTICE:
- Turn all electrical systems and the A/C off.
- Inspect the ignition timing with the cooling fan off.
- When checking the ignition timing, shift the transmission to the neutral position.
- Turn all electrical systems and the A/C off.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch off.
Remove the timing light.
Install the No. 2 cylinder head cover (Click here).
| 70. INSPECT ENGINE IDLING SPEED |
When using an intelligent tester:
Warm up and stop the engine.
Connect the intelligent tester to the DLC3.

Turn the ignition switch on (IG).
Select the following menu items: Powertrain / Engine and ECT /Data List / Engine Speed.
- HINT:
- Refer to the intelligent tester operator's manual for further details.
Inspect the engine idling speed.
- Idling speed:
- 600 to 700rpm
- NOTICE:
- Turn all electrical systems and the A/C off.
- Inspect the idling speed with the cooling fan off.
- When checking the idling speed, shift the transmission to either the neutral position or the parking position.
- Turn all electrical systems and the A/C off.
Turn the ignition switch off.
Disconnect the intelligent tester from the DCL3.
When not using an intelligent tester:
Warm up and stop the engine.
Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.

- SST
- 09843-18040
- NOTICE:
- Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
Turn the ignition switch on (IG).
Inspect the engine idling speed.
- Idling speed:
- 600 to 700rpm
Turn the ignition switch off.
Disconnect the tachometer.
Remove SST from terminal 9 (TAC).
| 71. INSPECT CO/HC |
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.
Check the CO/HC concentration during idling and when running at 2500 rpm.
- HINT:
- When doing the 2 mode (with the engine idling/running at 2500 rpm) test, the measuring procedures are determined by applicable local regulations.
Check the heated oxygen sensor operation (Click here).
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
CO
HC
Problems
Possible Causes
Normal
High
Rough idling
- Faulty ignition:
- Incorrect timing
- Fouled, shorted or improperly gapped plugs
- Incorrect valve clearance
- Leakage from intake and exhaust valves
- Leakage from cylinders
Low
High
Rough idling
(Fluctuating HC reading)
- Vacuum leaks:
- PCV hoses
- Intake manifold
- Throttle body
- Brake booster line
- Lean mixture causing misfire
High
High
Rough idling
(Black smoke from exhaust)
- Restricted air cleaner filter element
- Plugged PCV valve
- Faulty EFI systems:
- Faulty pressure regulator
- Faulty engine coolant temperature sensor
- Faulty mass air flow meter
- Faulty ECM
- Faulty injectors
- Throttle body
- Faulty ignition:
| 72. INSPECT FRONT WHEEL ALIGNMENT |
| 73. INSPECT ABS SENSOR SIGNAL |
Check the connector case and terminals for any deformation or corrosion.
- Standard:
- No deformation or corrosion.





























