2005-2008 Yaris · Service Manual ENGINE

Fuel Pump Control Circuit

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

When the engine is cranked, the starter relay drive signal output from the STAR terminal of the ECM is input to the STA terminal of the ECM, and NE signal generated by the crankshaft position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns the transistor Tr1 in the ECM internal circuit ON. The current flows to the C/OPN (Circuit Opening) relay by turning the Tr1 ON. Then, the fuel pump operates.
While the NE signal is input to the ECM with the while engine running, the ECM turns the Tr1 on continuously.
A105322E01

WIRING DIAGRAM

A116125E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.

    OK:
    Fuel pump operating sound occurs.



OK
Go to step 8
NG


2. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (C/OPN RELAY INPUT VOLTAGE)
A116124E01
  1. Measure the voltage between the terminal of the instrument panel junction block and the body ground when the ignition switch is on (IG) and off.

    Standard voltage:
    Tester Connection
    Ignition Switch Condition
    Specified Condition
    4B-11 - Body ground
    Off
    Below 1 V
    4F-4 - Body ground
    Off
    Below 1 V
    4B-11 - Body ground
    On (IG)
    10 to 14 V
    4F-4 - Body ground
    On (IG)
    10 to 14 V



OK
Go to step 4
NG


3. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B - INTEGRATION RELAY)
A107914E03
  1. Remove the integration relay from the engine room relay block.

  1. A116124E06
    Disconnect the instrument panel junction block connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    1B-4 - 4F-4
    Below 1 Ω
    1A-8 - 4B-11
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    4F-4 - Body ground
    10 kΩ or higher
    4B-11 - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the instrument panel junction block connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT

4. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)
A116124E03
  1. Remove the instrument panel junction block assembly.

  1. Connect the battery positive terminal to the 4D-1 terminal, and connect the battery negative terminal to the 4E-5 terminal.

  1. Check the C/OPN relay resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    4A-8 - 4B-11
    10 kΩ or higher
    4A-8 - 4B-11
    Below 1 Ω
    (when battery voltage applied to terminal 4D-1 and 4E-5)

    HINT:
    The relay coil circuit between 4D-1 and 4E-5 is not through the IGN fuse.

  1. Reinstall the instrument panel junction block assembly.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B - ECM)
A116124E05
  1. Disconnect the instrument panel junction block connector.

  1. A116135E01
    Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    4E-5 - FC (C33-63)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    FC (C33-63) - Body ground
    10 kΩ or higher

  1. Reconnect the instrument panel junction block connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL J/B - FUEL PUMP - BODY GROUND)
A116150E01
  1. Check the harness and the connectors between the instrument panel junction block assembly and the fuel pump.

    1. Disconnect the instrument panel junction block connector.

    2. Disconnect the fuel pump connector.

    3. Check the resistance.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      4A-8 - Fuel pump (J5-4)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      4A-8 - Body ground
      10 kΩ or higher

    4. Reconnect the instrument panel junction block connector.

    5. Reconnect the fuel pump connector.

  1. Check the harness and connector between the fuel pump and the body ground.

    1. Disconnect the fuel pump connector.

    2. Check the resistance.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      Fuel pump (J5-5) - Body ground
      Below 1 Ω

    3. Reconnect the fuel pump connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT FUEL PUMP
A095616E04
  1. Inspect fuel pump resistance.

    1. Measure the resistance between the fuel pump terminals.

      Standard resistance:
      0.2 to 3.0 Ω at 20°C (68°F)

  1. Inspect fuel pump operation.

    1. Apply battery voltage to the fuel pump terminals.

    2. Check that the fuel pump operates.

      NOTICE:
      1. This test must be done quickly (within 10 seconds) to prevent the coil from burning out.
      2. Keep the fuel pump as far away from the battery as possible.
      3. Always switch at the battery side.



NG
REPLACE FUEL PUMP
OK

REPLACE ECM

8. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is on (IG).

  1. Check the result when the engine starts.

    Standard:
    Ignition Switch Condition
    Tester Display (Starter Signal)
    On (IG)
    OFF
    Engine Start
    ON



NG
REPAIR OR REPLACE STARTING SYSTEM
OK


9. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Read the value while cranking.

    OK:
    The value is the same as the actual engine speed and is displayed with no interruption on the tester.



NG
REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR CIRCUIT
OK

REPLACE ECM


← ECM Back-up Power Source Circuit (from Aug 2005)Cranking Holding Function Circuit (from Aug 2005) →