2005-2008 Yaris · Service Manual ENGINE

Cranking Holding Function Circuit

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

The cranking holding control system keeps energizing the starter relay after the ECM detects the starter signal (STSW signal) from the ignition switch or the main body ECU until the ECM performs a judgement of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC cut relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.
When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the clutch start switch (or the park/neutral position switch), and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal. Also, the ECM monitors the starter relay operating conditions based on the STA terminal voltage status.
A133469E02

WIRING DIAGRAM

A116126E08
A120375E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned on (IG).

  1. Check the result when the engine starts.

    Standard:
    Ignition Switch Condition
    Tester Display (Starter Signal)
    On (IG)
    OFF
    Engine starts
    ON



OK
Go to step 12
NG


2. INSPECT ECM (STSW TERMINAL VOLTAGE)
A116134E04
  1. Park the vehicle with the transmission gear in neutral (for MMT models).

  1. Disconnect the ECM connector.

  1. Depress the brake pedal.

  1. Depress the clutch pedal fully (for M/T models).

  1. Measure the voltage between the ECM terminal and the body ground when operating the ignition switch to start cranking.

    Standard voltage:
    Tester Connection
    Specified Condition
    STSW (A32-12) - Body ground
    10 to 14 V

  1. Reconnect the ECM connector.

    Result:
    Result
    Proceed To
    Within standard range
    A
    Outside standard range (vehicle without entry and start system)
    B
    Outside standard range (vehicle with entry and start system)
    C

  1. Connect the intelligent tester to the DLC3, and check the DTC output. If any DTC outputs, erase the DTC using the tester.

    HINT:
    DTCs related CAN communication might be detected due to the inspection in this step.



B
Go to step 5

C
Go to step 6
A


3. INSPECT ECM (STAR OUTPUT VOLTAGE)
A122550E03
  1. Inspect the STAR output voltage (for M/T models).

    1. Disconnect the clutch start switch assembly connector.

    2. Measure the voltage between the terminal of clutch start switch assembly connector and the body ground while cranking the engine.

      Standard voltage:
      Tester Connection
      Specified Condition
      B (A16-2) - Body ground
      10 to 14 V

    3. Reconnect the clutch start switch assembly connector.

  1. Inspect the STAR output voltage (for MMT models).

    1. Disconnect the Park/Neutral Position (PNP) switch assembly connector.

    2. Measure the voltage between the terminal of PNP switch assembly connector and the body ground while cranking the engine.

      Standard voltage:
      Tester Connection
      Specified Condition
      B (A43-2) - Body ground
      10 to 14 V

    3. Reconnect the PNP switch assembly connector.


Result:
Result
Proceed To
Within standard range
A
Outside standard range (vehicle without entry and start system)
B
Outside standard range (vehicle with entry and start system)
C



B
Go to step 7

C
Go to step 8
A


4. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (MMT) OR CLUTCH START SWITCH ASSEMBLY (M/T)
A122558E04
  1. Inspect the clutch start switch assembly (for M/T models).

    1. Remove the clutch start switch assembly.

    2. Measure the resistance between the terminals of the clutch start switch assembly connector.

      Standard resistance:
      Switch Condition
      Specified Condition
      Pushed in
      Below 1 Ω
      Released
      10 kΩ or higher

    3. Reinstall the clutch start switch assembly.

  1. Inspect the Park/Neutral Position (PNP) switch assembly (for MMT models).

    1. Remove the PNP switch assembly.

    2. Measure the resistance between the terminals of the PNP switch assembly.

      Standard resistance:
      Switch Condition
      Tester Connection
      Specified Condition
      Pushed
      1 - 2
      Below 1 Ω
      Free
      1 - 2
      10 kΩ or higher

    3. Reinstall the PNP switch assembly.



OK
Go to step 12
NG

REPLACE CLUTCH START SWITCH ASSEMBLY

5. INSPECT IGNITION SWITCH
A107906E03
  1. Remove the ignition switch.

  1. Measure the resistance between the terminals of the ignition switch.

    Standard resistance:
    Switch Position
    Tester Connection
    Specified Condition
    LOCK
    -
    10 kΩ or higher
    ACC
    2 - 4
    Below 1 Ω
    ON
    1 - 2 - 4
    Below 1 Ω
    5 - 6
    Below 1 Ω
    START
    1 - 3 - 4
    Below 1 Ω
    5 - 6 - 7
    Below 1 Ω

  1. Reinstall the ignition switch.



NG
REPLACE IGNITION SWITCH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - IGNITION SWITCH - BATTERY)

6. CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU)
A116128E01
  1. Disconnect the main body ECU connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    STSW (D66-4) - STSW (A32-12)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    STSW (D66-4) - Body ground
    Below 1 Ω

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ENTRY AND START SYSTEM

7. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - IG SWITCH AND ECM, OR PNP SWITCH - ECM)
A120370E01
  1. Check harness and connectors (for M/T models).

    1. Disconnect the ignition switch connector.

    2. Disconnect the clutch start switch assembly connector.

    3. Disconnect the ECM connector.

    4. Check the resistance.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      ST2 (D8-7) - B (A16-2)
      Below 1 Ω
      STAR (A32-80) - B (A16-2)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      ST2 (D8-7) - Body ground
      10 kΩ or higher
      STAR (A32-80) - Body ground
      10 kΩ or higher

      HINT:
      The wire between the clutch start switch and the ignition switch has a diode (Refer to the wiring diagram). The current flowing to the clutch start switch is rectified by the diode.

    5. Reconnect the ignition switch connector.

    6. Reconnect the clutch start switch assembly connector.

    7. Reconnect the ECM connector.

  1. Check harness and connectors (for MMT models).

    1. Disconnect the ECM connector.

    2. Disconnect the Park/Neutral Position (PNP) switch assembly connector.

    3. Check the resistance.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      STAR (A32-80) - B (A43-2)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      STAR (A32-80) - Body ground
      10 kΩ or higher

    4. Reconnect the ECM connector.

    5. Reconnect the PNP switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

8. INSPECT ST CUT RELAY
B016200E02
  1. Remove the ST CUT relay.

  1. Check the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (When battery voltage applied to terminals 1 and 2)

  1. Reinstall the relay.



NG
REPLACE ST CUT RELAY
OK


9. INSPECT ST CUT RELAY (RELAY HOLDER TERMINAL VOLTAGE)
A122713E01
  1. Remove the ST CUT relay.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of the ST CUT relay holder.

    Standard voltage:
    Tester Connection
    Specified Condition
    1 - 2
    10 to 14 V

  1. Reinstall the relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK HARNESS AND CONNECTOR (ST CUT RELAY - ECM, MAIN BODY ECU, PNP AND CLUTCH ST SWITCH)
A120371E01
  1. Remove the ST CUT relay.

  1. Disconnect the clutch start switch assembly connector (for M/T models).

  1. Disconnect the Park/Neutral Position (PNP) switch assembly (for MMT models).

  1. Disconnect the main body ECU connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    ST CUT relay (D67-3) - STAR (A32-80)
    Below 1 Ω
    ST CUT relay (D67-3) - STR2 (D66-14)
    Below 1 Ω
    STR (D66-3) - ST CUT relay (D67-5)
    Below 1 Ω
    For M/T models:
    B (A16-2) - ST CUT relay (D67-5)
    For MMT models:
    B (A43-2) - ST CUT relay (D67-5)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    ST CUT relay (D67-3) - Body ground
    10 kΩ or higher
    ST CUT relay (D67-5) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the main body ECU connector.

  1. Reconnect the clutch start switch assembly connector (for M/T models).

  1. Reconnect the PNP switch assembly connector (for MMT models).

  1. Reinstall the ST CUT relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. INSPECT MAIN BODY ECU (CHECK FOR SHORT)
A122713E01
  1. Disconnect the ECM connector.

  1. Disconnect the clutch start switch assembly connector (for M/T models).

  1. Disconnect the Park/Neutral Position (PNP) switch assembly (for MMT models).

  1. Remove the ST CUT relay.

  1. Check the resistance between the terminals of the ST CUT relay holder.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    ST CUT relay (D67-3) - Body ground
    10 kΩ or higher
    ST CUT relay (D67-5) - Body ground
    10 kΩ or higher

  1. Reinstall the ST CUT relay.

  1. Reconnect the clutch start switch assembly connector (for M/T models).

  1. Reconnect the PNP switch assembly connector (for MMT models).

  1. Reconnect the ECM connector.



NG
CHECK ENTRY AND START SYSTEM
OK

REPLACE ECM

12. INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted.



NG
REPLACE BATTERY
OK


13. CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK


14. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH OR PNP SWITCH - ECM, ST RELAY)
A120372E01
  1. Check harness and connectors (for M/T models).

    1. Remove the ST relay from the engine room relay block.

    2. Disconnect the clutch start switch assembly connector.

    3. Disconnect the ECM connector.

    4. Check the resistance.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      L (A16-1) - STA (A32-27)
      Below 1 Ω
      L (A16-1) - ST relay (2)
      Below 1 Ω
      ST relay (1) - Body ground
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      L (A16-1) - Body ground
      10 kΩ or higher

    5. Reinstall the ST relay.

    6. Reconnect the clutch start switch assembly connector.

    7. Reconnect the ECM connector.

  1. Check harness and connectors (for MMT models).

    1. Remove the ST relay from the engine room relay block.

    2. Disconnect the Park/Neutral Position (PNP) switch assembly connector.

    3. Disconnect the ECM connector.

    4. Check the resistance.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      L (A43-1) - STA (A32-27)
      Below 1 Ω
      L (43-1) - ST relay (2)
      Below 1 Ω
      ST relay (1) - Body ground
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      L (A43-1) - Body ground
      10 kΩ or higher

    5. Reinstall the ST relay.

    6. Reconnect the PNP switch assembly connector.

    7. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK AND REPLACE STARTER CIRCUIT (STARTER - ST RELAY - BATTERY)


← Fuel Pump Control Circuit (from Aug 2005)MIL Circuit (from Aug 2005) →