2005-2008 Yaris · Service Manual ENGINE

VC Output Circuit

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor while the ignition switch is on (engine running). The ECM also provides this power to the sensors through the VC output circuit.
A116143E02
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned on (IG). The MIL goes off when the engine is started.


WIRING DIAGRAM

A116144E01

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).


1. CHECK MIL CONDITION
  1. Check that Malfunction Indicator Lamp (MIL) illuminates when turning the ignition switch on (IG).

    OK:
    MIL illuminates



OK
SYSTEM OK
NG


2. CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and the tester ON.

  1. Check the communication between the intelligent tester and ECM.

    Result:
    Result
    Proceed To
    Communication is possible
    A
    Communication is impossible
    B



A
GO TO MIL CIRCUIT
B


3. CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the throttle body connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL is illuminated
    A
    MIL is not illuminated
    B

  1. Reconnect the throttle body connector.



A
REPLACE THROTTLE BODY
B


4. CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL is illuminated
    A
    MIL is not illuminated
    B

  1. Reconnect the manifold absolute pressure sensor connector.



A
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
B


5. CHECK MIL (ACCELERATOR PEDAL)
  1. Disconnect the accelerator pedal connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL is illuminated
    A
    MIL is not illuminated
    B

  1. Reconnect the accelerator pedal connector.



A
REPLACE ACCELERATOR PEDAL
B


6. CHECK MIL (CAMSHAFT POSITION SENSOR)
  1. Disconnect the camshaft position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed To
    MIL is illuminated
    A
    MIL is not illuminated
    B

  1. Reconnect the camshaft position sensor connector.



A
REPLACE CAMSHAFT POSITION SENSOR
B


7. CHECK HARNESS AND CONNECTOR (VC CIRCUIT)
A116145E01
  1. Disconnect the throttle body connector.

  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the accelerator pedal connector.

  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connectors.

  1. Check the resistance.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    VC (C33-54) - Body ground
    10 k Ω or higher
    VC2 (C33-40) - Body ground
    10 k Ω or higher
    VC2R (C33-74) - Body ground
    10 k Ω or higher
    VCPA (A32-11) - Body ground
    10 k Ω or higher
    VCP2 (A32-19) - Body ground
    10 k Ω or higher

  1. Reconnect the throttle body connector, manifold absolute pressure sensor connector, accelerator pedal connector, and camshaft position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← ECM Power Source Circuit (from Aug 2005)ECM Back-up Power Source Circuit (from Aug 2005) →