2005-2008 Yaris · Service Manual BRAKE

C1249/49 Open in Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

The skid control ECU detects the brake operating conditions through a signal transmitted by the stop light switch. The skid control ECU incorporates an open circuit detection circuit.
DTC No.
DTC Detecting Conditions
Trouble Areas
C1249/49
When either of following (1 or 2) detected:
  1. Vehicle driven at 20 km/h (12 mph) or more for 6 minutes or more with stop light switch signal on
  2. During deceleration from 40 km/h (24 mph) to 3 km/h (2 mph), no change occurs in the stop light switch signal 4 times
  1. Stop light switch
  2. Stop light switch circuit
  3. Brake actuator (skid control ECU)

WIRING DIAGRAM

C136888E02

INSPECTION PROCEDURE


1. CHECK STOP LIGHT SWITCH OPERATION

  1. A107926E08
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the DATA LIST mode on the intelligent tester.Select the following menu items: Chassis / ABS/VSC/TRC / Data List.

    DATA LIST: ABS/VSC/TRC 
    Item (Display)
    Measurement Item : Range (Display)
    Normal Conditions
    Stop Lamp SW
    Stop light switch ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released

  1. Check that "Stop Lamp SW" is turned ON and OFF when the brake pedal is depressed and released.

    OK:
    "Stop Lamp SW" is turned ON and OFF in accordance with the operation of the brake pedal.



NG
Go to step 3
OK


2. CHECK SKID CONTROL ECU TERMINAL VOLTAGE (STP)
  1. Disconnect the skid control ECU connector.

  1. C129347E05
    Measure the voltage.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A39-4 (STP) - Body ground
    Brake pedal depressed
    10 to 14 V
    A39-4 (STP) - Body ground
    Brake pedal released
    Below 4.0 V



NG
Go to step 5
OK

REPLACE BRAKE ACTUATOR

3. INSPECT FUSE (STOP)

  1. C118695E01
    Remove the STOP fuse from the main body ECU.

  1. Measure the resistance.

    Standard Resistance:
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


4. INSPECT STOP LIGHT SWITCH ASSEMBLY
C118699E01
  1. Disconnect the stop light switch connector.

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Switch pin released
    Below 1 Ω
    3 - 4
    Switch pin released
    10 kΩ or higher
    1 - 2
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin pushed in
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)
  1. Disconnect the skid control ECU connector and stop light switch connector.

  1. C129373E01
    Measure the resistance.

    Standard Resistance:
    Tester Connection
    Specified Condition
    A39-4 (STP) - A13-1
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE BRAKE ACTUATOR


← C1241/41 Low Battery Positive Voltage or Abnormally High Battery Positive Voltage (from Nov 2005)C1251/51 Open in Pump Motor Circuit (from Nov 2005) →