2005-2008 Yaris · Service Manual BRAKE

C1231/31 Steering Angle Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

The steering angle sensor signal is sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the diagnostic function.
DTC No.
DTC Detecting Condition
Trouble Areas
C1231/31
When any of following conditions detected:
  1. Skid control ECU receives abnormal signals from steering angle sensor
  2. Skid control ECU receives abnormal voltage signals from steering angle sensor
  3. Despite calibration being conducted by skid control ECU, it does not finish within 15 seconds
  4. Abnormal difference between yaw rate and deceleration sensor and steering angle sensor signals continues for approximately 2 seconds or more during driving.
  1. Steering angle sensor
  2. Steering angle sensor circuit
  3. Steering angle sensor power supply
  4. CAN communication system

HINT:
DTC C1231/31 is erased automatically when the ignition switch is turned from off to on (IG) after the voltage supply to the steering angle sensor returns to normal.


WIRING DIAGRAM

C121696E01
C118707E01

INSPECTION PROCEDURE

HINT:
When U0073/94, U0123/62, U0124/69 or U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0073/94, U0123/62, U0124/69 or U0126/63 first.

NOTICE:
When replacing the ABS and TRACTION actuator, perform zero point calibration (Click here).


1. READ VALUE OF DATA LIST (STEERING ANGLE SENSOR)

  1. A107926E08
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on.

  1. Turn the tester on.

  1. Check that the steering wheel is centered.

  1. Read the steering wheel turning angle using the intelligent tester.Select the following menu items: Chassis / ABS/VSC/TRC / Data List.

    DATA LIST: ABS/VSC/TRC 
    Item (Display)
    Measurement Item: Range (Display)
    Normal Condition
    Steering Angle Sensor
    Steering angle sensor reading:
    min.: -3276.8 deg, max.: 3276.7 deg
    Left turn: Increase
    Right turn: Decrease
    Steering Angle Value
    Steering angle value:
    min.: -3276.8 deg, max.: 3276.7 deg
    Left turn: Increase
    Right turn: Decrease

  1. Check that the steering wheel turning angle of the steering angle sensor changes when turning the steering wheel.

    OK:
    Turning the steering wheel to the left: Value increases
    Turning the steering wheel to the right: Value decreases



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle and turn the steering wheel to the right and left at a speed of 45km/h (28 mph) or more for several seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE ABS AND TRACTION ACTUATOR

3. CHECK CAN COMMUNICATION SYSTEM
  1. Check if the CAN communication system DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
REPAIR CAN COMMUNICATION SYSTEM
A


4. CHECK STEERING ANGLE SENSOR
  1. Check that the steering angle sensor has been installed correctly (Click here).

    OK:
    The sensor is installed correctly.



NG
INSTALL STEERING ANGLE SENSOR CORRECTLY
OK


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STEERING ANGLE SENSOR)

  1. C122523E01
    Remove the steering wheel and the column cover lower.

  1. Disconnect the steering angle sensor connector.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Conditions
    D62-1(IG) - Body ground
    Ignition switch on (IG)
    10 to 14 V
    D62-3 (BAT) - Body ground
    Always
    10 to 14 V

  1. Measure the resistance.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Conditions
    D62-2 (ESS) - Body ground
    Ignition switch off
    Below 1Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE STEERING ANGLE SENSOR
  1. Replace the steering angle sensor (Click here).


NEXT


7. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle and turn the steering wheel to the right and left at a speed of 45km/h (28 mph) or more for several seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE ABS AND TRACTION ACTUATOR


← C1223/43 ABS Control System Malfunction (from Nov 2005)C1241/41 Low Battery Positive Voltage or Abnormally High Battery Positive Voltage (from Nov 2005) →