2005-2008 Yaris · Service Manual ENGINE

P0652 Sensor Reference Voltage "B" Circuit Low

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

Refer to DTC P1120 (Click here ).
DTC No.
DTC Detection Conditions
Trouble Areas
P0652
Power voltage (5 V as standard) supplied from ECM to accelerator pedal position sensor is lower than threshold
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Accelerator pedal position sensor
  2. Open or short in accelerator pedal position sensor circuit
  3. ECM
P0653
Power voltage (5 V as standard) supplied from ECM to accelerator pedal position sensor is higher than threshold
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)

HINT:
These DTCs are set when the ignition switch is in the on (IG) position.


WIRING DIAGRAM

Refer to DTC P1120 (Click here).

INSPECTION PROCEDURE


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0652 AND/OR P0653)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0652 and/or P0653
    A
    P0652 and/or P0653 and other DTCs
    B

    HINT:
    If any DTCs other than P0652 and/or P0653 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A129238E01
    Disconnect the A20 accelerator pedal position sensor connector.

  1. Disconnect the A49 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VCPA (A49-34) - VCPA (A20-4)
    Below 1 Ω
    VPA (A49-15) - VPA (A20-6)
    EPA (A49-56) - EPA (A20-5)
    VCP2 (A49-33) - VCP2 (A20-1)
    VPA2 (A49-14) - VPA2 (A20-3)
    EPA2 (A49-55) - EPA2 (A20-2)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VCPA (A49-34) or VCPA (A20-4) - Body ground
    10 kΩ or higher
    VPA (A49-15) or VPA (A20-6) - Body ground
    EPA (A49-56) or EPA (A20-5) - Body ground
    VCP2 (A49-33) or VCP2 (A20-1) - Body ground
    VPA2 (A49-14) or VPA2 (A20-3) - Body ground
    EPA2 (A49-55) or EPA2 (A20-2) - Body ground

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. INSPECT ECM (VC VOLTAGE)

  1. A109192E03
    Disconnect the A20 accelerator pedal position sensor connector.

  1. Measure the voltage between the terminals of the accelerator pedal position sensor connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    VCP2 (A20-1) - EPA2 (A20-2)
    4.5 to 5.5 V
    VCPA (A20-4) - EPA (A20-5)

  1. Reconnect the accelerator pedal position sensor connector.



NG
REPLACE ECM
OK

REPLACE ACCELERATOR PEDAL ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR)


← P0642 Sensor Reference Voltage "A" Circuit Low (+ P0643) (from Nov 2005)P0685 ECM / PCM Power Relay Control Circuit / Open (from Nov 2005) →