2005-2008 Yaris · Service Manual ENGINE

P0642 Sensor Reference Voltage "A" Circuit Low

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

Refer to DTC P0122 (Click here) and DTC P1120 (Click here).
DTC No.
DTC Detection Conditions
Trouble Areas
P0642
Power voltages (5 V as standard) supplied from ECM to both intake shutter position and accelerator pedal position sensors are lower than appropriate thresholds
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Intake shutter position sensor
  2. Open or short in intake shutter position sensor circuit
  3. Accelerator pedal position sensor
  4. Open or short in accelerator pedal position sensor circuit
  5. ECM
P0643
Power voltages (5 V as standard) supplied from ECM to both intake shutter position and accelerator pedal position sensors are higher than appropriate thresholds
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Intake shutter position sensor
  2. Open or short in intake shutter position sensor circuit
  3. Accelerator pedal position sensor
  4. Open or short in accelerator pedal position sensor circuit
  5. ECM

HINT:
These DTCs are set when the ignition switch is in the on (IG) position.


WIRING DIAGRAM

Refer to DTC P0122 (Click here) and DTC P1120 (Click here).

INSPECTION PROCEDURE


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0642 AND/OR P0643)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0642 and/or P0643
    A
    P0642 and/or P0643 and other DTCs
    B

    HINT:
    If any DTCs other than P0642 and/or P0634 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. CHECK HARNESS AND CONNECTOR (INTAKE SHUTTER (THROTTLE VALVE) POSITION SENSOR - ECM)

  1. A122649E01
    Disconnect the C58 intake shutter position sensor connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VVLU (C50-27) - VC (C58-1)
    Below 1 Ω
    VLU (C50-35) - VTA (C58-3)
    EVLU (C50-14) - E2 (C58-2)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VVLU (C50-27) or VC (C58-1) - Body ground
    10 kΩ or higher
    VLU (C50-35) or VTA (C58-3) - Body ground
    EVLU (C50-14) or E2 (C58-2) - Body ground

  1. Reconnect the intake shutter position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (VC VOLTAGE)

  1. A122648E01
    Disconnect the C58 intake shutter position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of the C58 intake shutter position sensor connector.

    Standard:
    Tester Connections
    Specified Conditions
    VC (C58-1) - E2 (C58-2)
    4.5 to 5.5 V

  1. Reconnect the intake shutter position sensor connector.



NG
REPLACE ECM
OK


4. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A129238E01
    Disconnect the A20 accelerator pedal position sensor connector.

  1. Disconnect the A49 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VCPA (A49-34) - VCPA (A20-4)
    Below 1 Ω
    VPA (A49-15) - VPA (A20-6)
    EPA (A49-56) - EPA (A20-5)
    VCP2 (A49-33) - VCP2 (A20-1)
    VPA2 (A49-14) - VPA2 (A20-3)
    EPA2 (A49-55) - EPA2 (A20-2)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VCPA (A49-34) or VCPA (A20-4) - Body ground
    10 kΩ or higher
    VPA (A49-15) or VPA (A20-6) - Body ground
    EPA (A49-56) or EPA (A20-5) - Body ground
    VCP2 (A49-33) or VCP2 (A20-1) - Body ground
    VPA2 (A49-14) or VPA2 (A20-3) - Body ground
    EPA2 (A49-55) or EPA2 (A20-2) - Body ground

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT ECM (VC VOLTAGE)

  1. A109192E03
    Disconnect the A20 accelerator pedal position sensor connector.

  1. Measure the voltage between the terminals of the accelerator pedal position sensor connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    VCP2 (A20-1) - EPA2 (A20-2)
    4.5 to 5.5 V
    VCPA (A20-4) - EPA (A20-5)

  1. Reconnect the accelerator pedal position sensor connector.



NG
REPLACE ECM
OK

REPLACE ACCELERATOR PEDAL ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR)


← P0603 Internal Control Module Keep Alive Memory (KAM) Error (from Nov 2005)P0652 Sensor Reference Voltage "B" Circuit Low (+ P0653) (from Nov 2005) →