2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2006


1. INSTALL OIL PUMP ASSEMBLY

  1. A150895
    Install the oil pump assembly with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


2. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
  1. Remove any old packing material from the contact surface.

  1. A150920E02
    Apply seal packing in a continuous bead (diameter: 4 mm (0.157 in.)) to the places shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the No. 2 oil pan sup-assembly within 3 minutes and tighten the bolts within 15 minutes of applying the seal packing.
    3. Do not expose the seal to engine oil for 2 hours after installation.

  1. A150894
    Install the No. 2 oil pan sub-assembly with the 10 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


3. INSTALL NO. 2 CHAIN SUB-ASSEMBLY

  1. A152671
    Set the crankshaft key as shown in the illustration.

  1. Turn the drive shaft so that the cutout faces right.

  1. A152672E02
    Align the yellow mark links with the timing marks of each gear as shown in the illustration.

  1. Install the gears onto the crankshaft and oil pump shaft with the chain on the gears.

  1. Temporarily tighten the oil pump drive shaft gear with the nut.

  1. A150873
    Insert the damper spring into the adjusting hole, and then install the chain tensioner plate with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A150875E01
    Align the adjusting hole of the oil pump drive shaft gear with the groove of the oil pump.

  1. A150876E01
    Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft gear to lock the gear in position, and then tighten the nut.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }


4. INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET

  1. A150878
    Install the crankshaft timing gear or sprocket.


5. INSTALL CHAIN SUB-ASSEMBLY

  1. Check the No. 1 cylinder TDC/compression.

    1. Temporarily tighten the crankshaft pulley bolt.

    2. A153029E01
      Turn the crankshaft counterclockwise until the timing gear key is facing up.

    3. Remove the crankshaft pulley bolt.

    4. A153030E01
      Check the timing mark on each camshaft timing gear.

  1. A150935E01
    Align the mark plate (orange) with the timing mark as shown in the illustration and install the chain.

    HINT:
    1. Be sure to position the mark plate at the front of the engine.
    2. The mark plate on the camshaft side is colored orange.
    3. Do not pass the chain around the sprocket of the camshaft timing gear assembly. Only place it on the sprocket.
    4. Pass the chain through the No. 1 vibration damper.

  1. A150936
    Place the chain on the crankshaft without passing it around the shaft.

  1. A150937E01
    Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly counterclockwise to align the mark plate (orange) and timing mark.

    HINT:
    1. Be sure to position the mark plate at the front of the engine.
    2. The mark plate on the camshaft side is colored orange.

  1. Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly clockwise.

    HINT:
    When tensioning the chain, turn the camshaft timing gear assembly clockwise slowly to prevent the chain from being misaligned.

  1. A150939E01
    Align the mark plate (yellow) and timing mark and install the chain to the crankshaft timing gear.

    HINT:
    The mark plate on the crankshaft side is colored yellow.

  1. Recheck each timing mark at TDC/compression.

    A150938E01


6. INSTALL NO. 1 CHAIN VIBRATION DAMPER

  1. A153028
    Install the No. 1 chain vibration damper with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


7. INSTALL CHAIN TENSIONER SLIPPER

  1. A150870
    Install the chain tensioner slipper.


8. INSTALL NO. 2 CHAIN VIBRATION DAMPER

  1. A153395
    Install the No. 2 chain vibration damper with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


9. INSTALL TIMING CHAIN OR BELT COVER OIL SEAL

A150934E01
  1. Using SST, tap in a new oil seal until its surface is flush with the timing gear case edge.

    SST
    09223-22010  

  1. Apply a light coat of MP grease to the lip of the oil seal.

    NOTICE:
    1. Keep the lip free of foreign matter.
    1. Do not tap on the oil seal at an angle.
    1. Make sure that the oil seal edge does not stick out of the timing chain cover.


10. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.

    A150923E01

  1. A150890
    Install 3 new O-rings.

  1. Apply seal packing as shown in the illustration.

    A150922E01

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.0 mm (0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the chain cover within 3 minutes of applying the seal packing.
    3. Do not start the engine for at least 2 hours after installing.

  1. Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

    A163235E01

    NOTICE:
    1. When the contact surfaces are wet, wipe them with oil-free cloth before applying seal packing.
    2. Install the chain cover within 3 minutes and tighten the bolts within 15 minutes of applying the seal packing.
    3. Do not start the engine for at least 2 hours after installation.


    Apply seal packing as follows:
    Area
    Seal Packing Diameter
    Application Position from Inside Seal Line
    Seal packing
    Continuous Line Area
    3.0 mm (0.118 in.)
    2.5 mm (0.098 in.)
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
    Dashed Line Area
    4.0 mm (0.156 in.)
    3.0 mm (0.118 in.)
    Toyota Genuine Seal Packing Black 1282B, Three Bond 1282B or equivalent

  1. A150940
    Install a new gasket.

    NOTICE:
    Remove any oil from the contact surface.

  1. A150864
    Install 2 new O-rings.

  1. Install the timing chain cover with the 19 bolts as shown in the illustration.

    A161119E01

    Torque:
    Bolt A and C:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }
    Bolt B and D:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }
    Bolt E:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. When the contact surfaces are wet, wipe them with oil-free cloth before applying seal packing.
    2. Install the chain cover within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.
    4. Tighten bolt D through the engine mounting bracket, pressing it against the timing chain or belt cover sub-assembly.
    5. Tighten bolt C through the oil filter bracket, pressing it against the timing chain or belt cover sub-assembly.

    Bolt length:
    Item
    Length
    Bolt A and C
    35 mm (1.38 in.)
    Bolt B
    55 mm (2.16 in.)
    Bolt D
    80 mm (3.15 in.)
    Bolt E
    40 mm (1.57 in.)

  1. A150865
    Install the water pump with the 3 bolts.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }


11. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A162975E01
    Release the ratchet pawl, then fully push in the plunger and hook the hook on the pin so that the plunger is in the position shown in the illustration.

    NOTICE:
    Make sure that the cam engages the first tooth of the plunger to allow the hook to pass over the pin.

  1. A150932
    Install a new gasket, bracket and the No. 1 chain tensioner with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    If the hook releases the plunger while the chain tensioner is being installed, set the hook again.

  1. A161124E01
    Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.

  1. A161125E01
    Turn the crankshaft clockwise, then check that the plunger is extended.


12. INSTALL CRANKSHAFT PULLEY
  1. Align the pin hole in the crankshaft pulley with the pin position and install the crankshaft pulley.

  1. Provisionally install the bolt.

  1. A150861E02
    Using SST, tighten the bolt while holding the crankshaft pulley.
    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    190 N*m{ 1940 kgf*cm , 140 ft.*lbf }

    NOTICE:
    Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the timing chain or belt cover sub-assembly.


13. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A150852
    Install 3 new gaskets onto the No. 1 camshaft bearing cap.

  1. A161126
    Apply seal packing as shown the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. A150850
    Install the cylinder head cover with a new seal washer and the 13 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


14. INSTALL AIR TUBE ASSEMBLY

  1. A147590
    Install the air tube assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


15. INSTALL IGNITION COIL ASSEMBLY

  1. A147572
    Install the 4 ignition coil assemblies with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 4 ignition coil assembly connectors.


16. INSTALL THERMOSTAT
  1. Install a new gasket onto the thermostat.

  1. A147628E01
    Install the thermostat with the jiggle valve facing upward.

    HINT:
    The jiggle valve may be set within 10° on either side, as shown in the illustration.


17. INSTALL WATER INLET

A147625
  1. Install the water inlet with radiator hose with the 2 nuts.

    Torque:
    10 N*m{ 101 kgf*cm , 7 ft.*lbf }


18. INSTALL NO. 3 WATER BY-PASS HOSE

  1. A147655
    Install the No. 3 water by-pass hose with the clip.


19. INSTALL WATER INLET HOSE

  1. A147656
    Install the water inlet hose with the clip.


20. INSTALL FAN BELT ADJUSTING BAR

  1. A147584
    Install the fan belt adjusting bar with the bolt.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }


21. INSTALL GENERATOR ASSEMBLY

  1. A159363
    Provisionally install the generator assembly with the bolt.

  1. A159361
    Provisionally install the fan belt adjusting bar and generator assembly with the 2 bolts.

  1. A159383E01
    Tighten the bolt A to the specified torque.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }

  1. A159384
    Connect the connector and wire harness clamp.

  1. Install terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.


22. INSTALL OIL LEVEL GAGE GUIDE

  1. A147586
    Install a new O-ring.

  1. Install the oil level gage guide with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


23. INSTALL OIL LEVEL GAGE SUB-ASSEMBLY

24. INSTALL INTAKE MANIFOLD

  1. A147580
    Install a new gasket onto the intake manifold.

  1. Provisionally tighten the intake manifold and manifold stay with the 5 bolts and 2 nuts in the order shown in the illustration, and then tighten it to the specified torque.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. A147579
    Install the wire harness clamp onto the intake manifold.

  1. Install the water by-pass hose into the intake manifold.

  1. Install the ventilation hose into the intake manifold.

  1. Install the No. 1 vacuum transmitting hose with the clip.

  1. A147578
    Install the No. 1 fuel vapor feed hose into the throttle body manifold.

  1. Install the water by pass hose with the clip.


25. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Install the engine moving control rod with the through bolt.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }

  1. Remove the 2 bolts and remove the 2 engine hangers.


26. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

  1. A147570
    Set the engine assembly with transaxle and front suspension crossmember on the engine lifter.

  1. Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the engine mounting insulator RH and LH can be installed.

  1. A147569
    Install the engine mounting insulator LH with the through bolt and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. A147568E01
    Install the engine mounting insulator RH with the 6 bolts and nut.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf } for Bolt A
    45 N*m{ 459 kgf*cm , 33 ft.*lbf } for Bolt B
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for Nut C

  1. A159382
    Install the engine mounting stay RH with the 2 bolts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Operate the engine lifter and provisionally install the engine assembly with transaxle and front suspension crossmember onto the vehicle with the 6 bolts.

  1. A147571E01
    A117079E01
    Insert SST into the datum holes in the front suspension crossmember RH and LH alternately and tighten bolts A, B and C on both sides in several sequences.
    SST
    09670-00010  

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf } for Bolt A
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf } for Bolt B
    95 N*m{ 969 kgf*cm , 70 ft.*lbf } for Bolt C

    CAUTION:
    1. Insert SST into the datum hole vertically.
    2. If impossible to insert SST vertically, loosen all bolts and then insert SST again.


27. INSTALL FRONT AXLE ASSEMBLY LH
  1. Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Check for any foreign matter on the speed sensor rotor and insertion part.
    4. Do not damage the speed sensor rotor.


28. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


29. INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

  1. C107513
    Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.


30. INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


31. INSTALL FRONT STABILIZER LINK ASSEMBLY LH

  1. C106044
    Install the stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


32. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


33. INSTALL TIE ROD END SUB-ASSEMBLY LH

  1. C107961
    Install the tie rod end onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.


34. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


35. INSTALL SPEED SENSOR FRONT LH

C112274
  1. Install the speed sensor onto the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Check that the speed sensor tip and installation portion are free of foreign matter.
    2. Install the speed sensor without turning it from its original installation angle.

  1. C125274
    Install the flexible hose and speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.


36. INSTALL SPEED SENSOR FRONT RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


37. INSTALL FRONT AXLE SHAFT LH NUT

C057566
  1. Using a 30 mm socket wrench, install a new axle hub nut.

    Torque:
    216 N*m{ 2203 kgf*cm , 160 ft.*lbf }

  1. Using a chisel and hammer, caulk the axle hub nut.


38. INSTALL FRONT AXLE SHAFT RH NUT

HINT:
The installation procedure for the RH side is the same as that for the LH side.


39. INSTALL FRONT EXHAUST PIPE ASSEMBLY

  1. A104634
    Using vernier calipers, measure the free length of the compression spring.

    Minimum length (Front side):
    40.5 mm (1.594 in.)

    Minimum length (Rear side):
    38.5 (1.516 in.)

    If the length is not as specified, replace the compression spring.

  1. A104635E01
    Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Install the exhaust pipe gasket in the correct direction.
    2. Do not damage the outer surface of the exhaust pipe gasket.
    3. Do not reuse the exhaust pipe gasket.
    4. Do not push in the gasket with the exhaust pipe when connecting it.

  1. Install the 3 exhaust pipe support No. 4.

  1. Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }


40. INSTALL HEATED OXYGEN SENSOR

  1. A158287E01
    Using SST, install the heated oxygen sensor onto the front exhaust pipe.
    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }

  1. Pass the sensor connector through the floor panel and install the grommet.

  1. A158286
    Install the wire harness clamp bracket.

  1. A158285
    Connect the heated oxygen sensor connector.


41. INSTALL REAR CONSOLE BOX ASSEMBLY

B118993
  1. Engage the 2 clips and install the console box rear.

  1. Install bolt <F>.


42. INSTALL CONSOLE BOX REAR COVER

B118991
  1. Engage the 8 claws and install the console box rear cover.


43. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY

B118990
  1. Engage the 6 claws and install the shifting hole cover.


44. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

B118989
  1. Install the shift lever knob.


45. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

  1. C125686E01
    Install clip B onto the body portion and install column No. 1 onto the body portion with clip A.

    NOTICE:
    Make sure that the lip portion of hole cover No. 1 is not damaged.


46. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

C118005E03
  1. Align the matchmarks and install the sliding yoke onto the intermediate shaft.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }


47. INSTALL COLUMN HOLE COVER SILENCER SHEET

A116501
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.


48. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY

C106371E01
  1. Install the clutch release cylinder and clutch pipe with the 4 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 8.7 ft.*lbf } for bolt A
    12 N*m{ 122 kgf*cm , 8.9 ft.*lbf } for bolt B


49. CONNECT FUEL TUBE SUB-ASSEMBLY

  1. A147557
    Connect the fuel tube connector and fuel pipe, and install the No. 1 fuel pipe clamp.

    CAUTION:
    Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a click sound. If the connection is tight, apply a small amount of engine oil to the the tip of the pipe. After connecting, pull the pipe and connector to make sure that they are securely connected.


50. CONNECT HEATER WATER INLET HOSE A

  1. A147576
    Install heater water inlet hose A with the clip.


51. CONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)

  1. A147575
    Install heater water outlet hose A with the clip.


52. CONNECT ENGINE WIRE

  1. A147553
    Connect the 2 engine wire harness connectors and wire harness clamp to the engine room junction block.

  1. A147554
    Connect the engine wire harness connector to the ECM.

  1. Connect the wire harness clamp.

  1. A147552
    Connect the 2 connectors.

  1. A147551
    Install the transaxle earth wire with the bolt.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }

  1. Connect the 2 wire harness clamps.


53. INSTALL NO. 1 FUEL VAPOR FEED HOSE

  1. A147550
    Install the No. 1 fuel vapor feed hose into the vacuum switching valve assembly.


54. INSTALL UNION TO CHECK VALVE HOSE

  1. A147549
    Install the union to check valve hose with the clip.


55. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

C115305
  1. Connect the 2 cable ends and install the 2 washers and the 2 clips.

  1. Install 2 new clips onto the control cable bracket.


56. INSTALL WITH PULLEY COMPRESSOR ASSEMBLY

I103381
  1. Using "TORX" socket wrench E8, install the compressor with the 2 stud bolts.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. I103380E01
    Tighten the compressor with the 2 bolts and 2 nuts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Tighten the bolts in the following order: 1 (provisional tightening) → 2 → 3 → 4 → 1.

  1. Connect the connector and the clamp.


57. INSTALL RADIATOR ASSEMBLY

A147637
  1. Engage the 2 claws and install the radiator assembly onto the vehicle.

    NOTICE:
    Do not apply excessive force to the cooler condenser assembly or piping when installing the radiator assembly.

  1. A147635
    Connect the cooling fan motor connector and wire harness clamp.


58. INSTALL FAN SHROUD VENTILATION DUCT ASSEMBLY

A147636
  1. Engage the 4 claws and install the fan shroud ventilation duct assembly.

    NOTICE:
    Do not apply excessive force to the cooler condenser assembly or piping when installing the radiator assembly.


59. INSTALL RADIATOR SUPPORT SUB-ASSEMBLY UPPER

A147634
  1. Install the radiator support sub-assembly upper with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. A147633
    Connect the horn assembly connector.


60. INSTALL HOOD LOCK ASSEMBLY

A108456
  1. Install the hood lock assembly with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. A108455
    Install the hood lock control cable assembly with the 2 clamps.


61. INSTALL FRONT BUMPER COVER

  1. B160102
    Install the 2 clips, the 2 spring nuts and the screw grommet.

  1. B160100
    Connect the 2 fog light connectors.

  1. Engage the 6 claws and install the front bumper cover.

  1. B160161
    Install the 7 clips.

  1. B160098
    Install the 2 screw grommets.

  1. Install the 5 screws and the 3 bolts.

  1. B160160E01
    Remove the protective tape.


62. CONNECT NO. 1 RADIATOR HOSE

A147631
  1. Connect the No. 1 radiator hose with the clip.


63. INSTALL NO. 2 RADIATOR HOSE

  1. A147548
    Install the No. 2 radiator hose with the 2 clips.


64. INSTALL FAN AND GENERATOR V BELT
  1. Provisionally install the fan and generator V belt onto each pulley.

    NOTICE:
    Make sure that the V belt is securely fitted into the rib groove of the pulley.


65. ADJUST FAN AND GENERATOR V BELT

  1. A161127E01
    Turn adjusting bolt C and adjust the tension of the V belt.

    NOTICE:
    Check that bolt D is tightened to the specified torque of 19 N*m (189 kgf*cm, 14 ft.*lbf).

  1. Tighten fixing bolts A and B.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf } for bolt A
    43 N*m{ 438 kgf*cm , 32 ft.*lbf } for bolt B


66. INSPECT FAN AND GENERATOR V BELT

  1. A147660E02
    Check the V belt deflection and tension.

    Deflection:
    Item
    Specified Condition
    New belt
    7.5 to 8.6 mm (0.296 to 0.338 in.)
    Used belt
    8.0 to 10.0 mm (0.315 to 0.397 in.)

    Tension:
    Item
    Specified Condition
    New belt
    688 to 884 N (70 to 90 kg, 155 to 199 ld)
    Used belt
    402 to 598 N (40 to 61 kg, 90 to 134 ld)

    If the belt deflection is not as specified, adjust it.

    HINT:
    1. Check the V belt deflection at the specified point.
    2. When installing a new belt, set its tension to the specified value.
    3. When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.
    4. When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of the Used Belt specifications.
    5. V belt tension and deflection should be checked after 2 revolutions of engine cranking.
    6. When checking the tension, use a sonic tension meter.

    Input Data for Sonic Tension Meter

    Weight:
    15 g/rib*m

    Width:
    6 ribs (21.36 mm)

    Span:
    188 mm (w/ A/C)
    282 mm (w/o A/C)


67. INSTALL NO. 2 CYLINDER HEAD COVER

  1. A158207
    Disengage the 4 fittings shown and install the No. 2 cylinder head cover by applying pressure to it.

    HINT:
    Make sure that the oil and the engine oil level dipstick are correctly installed before installing the No. 2 cylinder head cover.


68. INSTALL BATTERY CARRIER

A117309
  1. Install the battery carrier with the 5 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Install the clamp.


69. INSTALL AIR CLEANER BRACKET

A117308
  1. Install the air cleaner bracket with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Connect the wire harness clamp to the air cleaner bracket.


70. INSTALL AIR CLEANER ASSEMBLY

A104895
  1. Install the air cleaner case with air cleaner inlet with the 2 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Connect the wire harness to the air cleaner case.

  1. Install the air cleaner element.

  1. A147547
    Install and lock the air cleaner cap with air cleaner hose and then tighten the air cleaner hose clamp.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Connect the ventilation hose to the air cleaner hose.

  1. Connect the intake air flow meter connector and wire harness clamp.


71. INSTALL COWL TOP PANEL OUTER

A115392
  1. Install the cowl top panel with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. A108438
    Connect the wire harness clamp.


72. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A108437
  1. Engage the claw to install No. 2 cowl to register duct.


73. INSTALL FRONT WIPER MOTOR AND LINK

E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


74. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.


75. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


76. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


77. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


78. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


79. INSTALL FRONT WIPER ARM LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


80. INSTALL FRONT WIPER ARM RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


81. INSTALL FRONT WIPER ARM HEAD CAP

E113849
  1. Engage the claw and install the 2 front wiper arm head caps.


82. INSTALL BATTERY TRAY

83. INSTALL BATTERY
  1. Install the battery onto the vehicle with the battery clamp.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the cable to the battery terminal.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


84. ADD ENGINE COOLANT
  1. Tighten all the plugs.

  1. Pour engine coolant into the radiator assembly until it is completely full.

    Capacity:
    5.0 liters (5.3 USqts, 4.4 lmp. qts)

    NOTICE:
    Do not substitute water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens.
      While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (b) through (g) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add engine coolant.


85. ADD ENGINE OIL
  1. Fill with new engine oil.

    Engine oil:
    Oil Grade
    Oil Viscosity (SAE)
    1. API grade SL and energy-conserving
    2. API grade SM and energy-conserving
    3. ILSAC multigrade engine oil
    1. 0W-20
    2. 5W-20
    3. 5W-30
    4. 10W-30
    1. API grade SL
    2. API grade SM
    1. 15W-40
    2. 20W-50

    Oil capacity:
    Item
    Capacity
    With oil filter change
    4.2 liters (4.4 US qts, 3.7 Imp. qts)
    Without oil filter change
    3.9 liters (4.1 US qts, 3.4 Imp. qts)
    Dry fill
    4.7 liters (5.0 US qts, 4.1 Imp. qts)


86. INSPECT FOR FUEL LEAK
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and the intelligent tester main switch ON.

    NOTICE:
    Do not start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.

  1. Check that there is no fuel leakage anywhere in the fuel system after doing maintenance.


87. INSPECT FOR ENGINE OIL LEAK

88. INSPECT FOR EXHAUST GAS LEAK

89. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A147619E01
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.


90. INSTALL ENGINE UNDER COVER RH

91. INSTALL ENGINE UNDER COVER LH

92. INSTALL FRONT WHEELS

93. INSPECT IGNITION TIMING

  1. When using an intelligent tester:

    1. Warm up and stop the engine.

    2. A117072E02
      Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG).

    4. Select the following menu items:
      Powertrain / Engine and ECT / Active Test / TC (TE1) / ON.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    5. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      1. Turn all electrical systems and the A/C off.
      2. Inspect the ignition timing with the cooling fan off.
      3. When checking the ignition timing, shift the transmission to the neutral position.

    6. Select the following menu items: TC (TE1) / OFF

    7. Turn the ignition switch off.

    8. Disconnect the intelligent tester from the DLC3.

  1. When not using an intelligent tester:

    1. Remove the No. 2 cylinder head cover (Click here).

    2. A150576
      Pull out the wire harness (brown) shown in the illustration.

      NOTICE:
      After checking, wrap the wire harness with tape.

    3. Warm up and stop the engine.

    4. Connect a timing light clip to the wire harness.

      NOTICE:
      Use a timing light that detects the first signal.

    5. Turn the ignition switch on (IG).

    6. A082779E23
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  

      NOTICE:
      Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    7. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      1. Turn all electrical systems and the A/C off.
      2. Inspect the ignition timing with the cooling fan off.
      3. When checking the ignition timing, shift the transmission to the neutral position.

    8. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    9. Turn the ignition switch off.

    10. Remove the timing light.

    11. Install the No. 2 cylinder head cover (Click here).


94. INSPECT ENGINE IDLING SPEED

  1. When using an intelligent tester:

    1. Warm up and stop the engine.

    2. A117072E02
      Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG).

    4. Select the following menu items: Powertrain / Engine and ECT /Data List / Engine Speed.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    5. Inspect the engine idling speed.

      Idling speed:
      600 to 700rpm

      NOTICE:
      1. Turn all electrical systems and the A/C off.
      2. Inspect the idling speed with the cooling fan off.
      3. When checking the idling speed, shift the transmission to either the neutral position or the parking position.

    6. Turn the ignition switch off.

    7. Disconnect the intelligent tester from the DCL3.

  1. When not using an intelligent tester:

    1. Warm up and stop the engine.

    2. A082779E24
      Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.
      SST
      09843-18040  

      NOTICE:
      Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    3. Turn the ignition switch on (IG).

    4. Inspect the engine idling speed.

      Idling speed:
      600 to 700rpm

    5. Turn the ignition switch off.

    6. Disconnect the tachometer.

    7. Remove SST from terminal 9 (TAC).


95. INSPECT CO/HC
  1. Start the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.

  1. Check the CO/HC concentration during idling and when running at 2500 rpm.

    HINT:
    When doing the 2 mode (with the engine idling/running at 2500 rpm) test, the measuring procedures are determined by applicable local regulations.

    If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.

    1. Check the heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

      CO
      HC
      Problems
      Possible Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        2. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leakage from intake and exhaust valves
      4. Leakage from cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idling
      (Black smoke from exhaust)
      1. Restricted air cleaner filter element
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        2. Faulty engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Throttle body


96. INSPECT FRONT WHEEL ALIGNMENT
(Click here)

97. INSPECT ABS SENSOR SIGNAL
← REASSEMBLY (from Nov 2006)PRECAUTION (from Aug 2005) →