Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Sedan)

DTC    C0210/33    Right Rear Wheel Speed Sensor Signal

DTC    C0215/34    Left Rear Wheel Speed Sensor Signal

DTC    C1238/38    Foreign Object is Attached on Tip of Rear Speed Sensor RH

DTC    C1239/39    Foreign Object is Attached on Tip of Rear Speed Sensor LH

DTC    C1273/73    Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1274/74    Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC    C1277/77    Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1278/78    Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)

for Preparation Click here


DESCRIPTION

Refer to DTC C0200/31 .

DTC No.
DTC Detecting Conditions
Trouble Areas
C0210/33
C0215/34
When any of following conditions detected:
  1. At vehicle speed of 10 km/h (6 mph) or more, open or short in sensor signal circuit continues for 1 second or more.
  2. Momentary interruption of sensor signal from abnormal wheel occurs 255 times or more.
  3. Open in speed sensor signal circuit continues for 0.5 seconds or more.
  4. With IG1 terminal voltage 9.5 V or more, sensor power supply voltage decreases for 0.5 seconds or more.
  5. When vehicle driven at speed of more than 10 km/h (6 mph), one of wheel speed below one-seventh of other wheel speeds for 15 seconds or more.
  1. Skid control sensor
  2. Skid control sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1238/38
C1239/39
When either of following conditions detected:
  1. At vehicle speed of 20 km/h (12 mph) or more, noise occurs 75 times or more in sensor signal from abnormal wheel in 5 seconds.
  2. At vehicle speed of 10 km/h (6 mph) or more, noise input once per rotor rotation for 15 seconds or more.
  1. Skid control sensor (open)
  2. Skid control sensor circuit (open)
C1273/73
C1274/74
Detected only during test mode.
  1. Skid control sensor
  2. Skid control sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1277/77
C1278/78
Detected only during test mode.
  1. Skid control sensor (open)
  2. Skid control sensor circuit (open)

HINT:
  1. DTC C0210/33 and C1238/38 relate to the skid control sensor RH.
  2. DTC C0215/34 and C1239/39 relate to the skid control sensor LH.


WIRING DIAGRAM


C117849E04


INSPECTION PROCEDURE

NOTICE:
  1. Disassembly of the skid control sensor from the rear axle hub and bearing assembly is prohibited.
  2. Check the skid control sensor signal in test mode after cleaning or replacement (Click here).

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)


    A107926E08
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Using the intelligent tester, check for any momentary interruption in the wire harness of the speed sensor.
    Select the following menu items: Chassis / ABS/VSC/TRC / Data List.

    DATA LIST: ABS 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    RR Speed Open
    RR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    RL Speed Open
    RL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal

    OK:
    There are no momentary interruptions.

    HINT:
    Perform this inspection before removing the sensor and connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


2.READ VALUE USING DATA LIST (SKID CONTROL SENSOR)


    A107926E08
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and drive the vehicle.

  1. Turn the tester on.

  1. Read the wheel speed value using the intelligent tester.
    Select the following menu items: Chassis / ABS/VSC/TRC / Data List.

  1. Select the item "RR (RL) Wheel Speed" in the DATA LIST and read the value displayed on the intelligent tester.

    DATA LIST: ABS 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    RR Wheel Speed
    Wheel speed sensor (RR) reading : min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Similar to speed indicated on speedometer
    RL Wheel Speed
    Wheel speed sensor (RL) reading : min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Similar to speed indicated on speedometer

  1. Check that there is no significant difference between the speed value displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    There is almost no difference in the displayed speed values.

    HINT:
    There is a tolerance of +- 10% in the speedometer indication.



NG
Go to step 5
OK


3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a TEST MODE inspection and check for DTCs (Click here).

    OK:
    No DTCs output.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


4.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 10
A

END 

5.CHECK SKID CONTROL SENSOR


    C118693E01
  1. Visually check the skid control sensor for deformation and damage.

    OK:
    No deformation or damage.
    There is no gap between the sensor and rear axle carrier.



NG
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (SKID CONTROL SENSOR) (Click here)
OK


6.INSPECT SKID CONTROL SENSOR WIRE
  1. Disconnect the skid control sensor wire.



    C129355E01
  1. Measure the resistance.

    Standard Resistance (LH):
    Tester Connection
    Specified Condition
    a1-1 - aJ1-1
    Below 1 Ω
    a1-1 - aJ-2
    10 kΩ or higher
    a1-1 - Body ground
    10 kΩ or higher
    a1-2 - aJ1-1
    10 kΩ or higher
    a1-2 - aJ1-2
    Below 1 Ω
    a1-2 - Body ground
    10 kΩ or higher

    Standard Resistance (RH):
    Tester Connection
    Specified Condition
    Z1-1 - ZJ1-1
    Below 1 Ω
    Z1-1 - ZJ-2
    10 kΩ or higher
    Z1-1 - Body ground
    10 kΩ or higher
    Z1-2 - ZJ1-1
    10 kΩ or higher
    Z1-2 - ZJ1-2
    Below 1 Ω
    Z1-2 - Body ground
    10 kΩ or higher



NG
REPLACE SKID CONTROL SENSOR WIRE
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR)
  1. Confirm that the skid control ECU connector and skid control sensor connector are properly connected.

  1. Disconnect the skid control ECU connector and the skid control sensor connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.



    C129356E01
  1. Measure the resistance.

    Standard Resistance (LH):
    Tester Connection
    Specified Condition
    A15-11 (RL+) - a1-2 (RL+)
    Below 1 Ω
    A15-12 (RL-) - a1-1 (RL-)
    Below 1 Ω

    Standard Resistance (RH):
    Tester Connection
    Specified Condition
    A15-33 (RR+) - Z1-2 (RR+)
    Below 1 Ω
    A15-34 (RR-) - Z1-1 (RR-)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


8.CHECK SKID CONTROL SENSOR (INPUT VOLTAGE)
  1. Disconnect the skid control sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Specified Condition
    a1-2 (RL+) - Body ground
    5.7 to 17.3 V
    Z1-2 (RR+) - Body ground
    5.7 to 17.3 V



NG
REPLACE BRAKE ACTUATOR (Click here)
OK


9.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (REAR SKID CONTROL SENSOR AND REAR SKID CONTROL SENSOR ROTOR)
  1. Turn the ignition switch off.

  1. Replace the rear speed sensor and rear axle hub and bearing assembly (Click here).

HINT:
The rear skid control sensor rotor is incorporated into the rear axle hub and bearing assembly.
Because the rear axle hub and bearing assembly cannot be disassembled. if the rear skid control sensor needs replacement, replace the rear axle hub and bearing assembly.

NOTICE:
Check the speed sensor signal after replacement (Click here).


NEXT


11.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE BRAKE ACTUATOR (Click here)