Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Hatchback)

DTC    C1405    Open or Short in Front Speed Sensor RH Circuit

DTC    C1406    Open or Short in Front Speed Sensor LH Circuit

for Preparation Click here


DESCRIPTION

Refer to DTCs C1401 and C1402 .

DTC Code
DTC Detection Condition
Trouble Area
C1405
C1406
When any of the following is detected:
  1. Open in speed sensor signal circuit continues for 0.5 seconds or more.
  2. With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Front speed sensor RH/LH
  2. Speed sensor circuit
  3. Brake actuator assembly (Skid control ECU)
C1271
C1272
Detected only during Test Mode.
  1. Front speed sensor RH/LH
  2. Sensor installation
  3. Speed sensor rotor

HINT:
  1. DTCs C1271 and C1272 are output only in the Test Mode.
  2. DTCs C1271 and C1272 can be deleted when the speed sensor sends a vehicle speed signal or the Test Mode ends.
  3. DTCs C1405 and C1271 are for the front speed sensor RH.
  4. DTCs C1406 and C1272 are for the front speed sensor LH.


WIRING DIAGRAM


C149728E20


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using an intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    FR speed sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    FL Speed Open
    FL speed sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -

    OK:
    There are no momentary interruptions

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 8
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

3.CHECK IF SKID CONTROL ECU AND FRONT SPEED SENSOR CONNECTORS ARE SECURELY CONNECTED
  1. Check if the skid control ECU and the front speed sensor connectors are securely connected.


NEXT


4.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


5.INSPECT FRONT SPEED SENSOR


    C109455E02
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    2 (FR+) - Body ground
    Always
    10 kΩ or higher
    1 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    2 (FL+) - Body ground
    Always
    10 kΩ or higher
    1 (FL-) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE FRONT SPEED SENSOR (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)


    C168929E04
  1. Disconnect the skid control ECU connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A15-7 (FR+) - A7-2 (FR+)
    Always
    Below 1 Ω
    A15-7 (FR+) - Body ground
    Always
    10 kΩ or higher
    A15-6 (FR-) - A7-1 (FR-)
    Always
    Below 1 Ω
    A15-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A15-19 (FL+) - A11-2 (FL+)
    Always
    Below 1 Ω
    A15-19 (FL+) - Body ground
    Always
    10 kΩ or higher
    A15-18 (FL-) - A11-1 (FL-)
    Always
    Below 1 Ω
    A15-18 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT SKID CONTROL ECU (SENSOR INPUT)


    C156480E21
  1. Reconnect the skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-2 (FR+) - Body ground
    Ignition switch ON
    8 to 14 V
    for LH:
    Tester Connection
    Switch Condition
    Specified Condition
    A11-2 (FL+) - Body ground
    Ignition switch ON
    8 to 14 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


8.REPLACE FRONT SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the front speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).


NEXT


9.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

END